T1 ToneMatch® Audio Engine: Difference between revisions

Line 68:

When using the Classic or Model I <ref>Hilmar-at-Bose talks about setting inputs [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=2991039944#2991039944]</ref>

The T1 has more input capability then the Model 1,s so you should be able to use the T1 as the only control for your system. We have a recommended trim setting for connecting the T1 to a Model 1 input Ch 3 or Ch 4 ~~(I think it~~'~~s 2)~~. With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.

The T1 has more input capability then the Model 1,s so you should be able to use the T1 as the only control for your system. We have a recommended trim setting for connecting the T1 to a Model 1 input Ch 3 or Ch 4

Note: New recommendation is '''3''' see below.

With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.

The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.

=== Input setting recommendation now '''3''' ===

MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the Model I or Classic Power Stand with the T1™] </ref>

Bill-at-Bose and I have revisited this.

For these conditions:

* T1 going into model I/Classic into Ch 3/4

* balanced OR unbalanced 1/4" cable

* remote unplugged, OR, master volume on remote at 12 o clock

* proper gain staging required on the T1 itself

I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.

This will give you the same gain going into the L1 Classic/model I as if you were going through the digital ethercon input on a model II.

If you are using the remote on your M1/CL, then you will need to compensate a bit. If you running the remote master volume at max, then stick with '''2'''on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1.

Hopefully this is helpful - please ask away with any questions for clarification.

MikeZ

Excerpt from the {{T1}} Manual - page 20

@@ Line 68: / Line 68: @@
 {{T1 icon}}{{Model I icon}}{{Classic icon}}
 When using the Classic or Model I <ref>Hilmar-at-Bose talks about setting inputs [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=2991039944#2991039944]</ref>
-The T1 has more input capability then the Model 1,s so you should be able to use the T1 as the only control for your system. We have a recommended trim setting for connecting the T1 to a Model 1 input Ch 3 or Ch 4 (I think it's 2). With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.
+The T1 has more input capability then the Model 1,s so you should be able to use the T1 as the only control for your system. We have a recommended trim setting for connecting the T1 to a Model 1 input Ch 3 or Ch 4
+Note: New recommendation is '''3''' see below.
+With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.
 The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.
+=== Input setting recommendation now '''3''' ===
+MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the Model I or Classic Power Stand with the T1™] </ref>
+Bill-at-Bose and I have revisited this.
+For these conditions:
+* T1 going into model I/Classic into Ch 3/4
+* balanced OR unbalanced 1/4" cable
+* remote unplugged, OR, master volume on remote at 12 o clock
+* proper gain staging required on the T1 itself
+I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.
+This will give you the same gain going into the L1 Classic/model I as if you were going through the digital ethercon input on a model II.
+If you are using the remote on your M1/CL, then you will need to compensate a bit. If you running the remote master volume at max, then stick with '''2'''on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1.
+Hopefully this is helpful - please ask away with any questions for clarification.
+MikeZ
 Excerpt from the {{T1}} Manual - page 20