|
|
| Line 28: |
Line 28: |
|
| |
|
| ==== Set Up ==== | | ==== Set Up ==== |
| # Turn down the volume on the S1 Pro+ system - all channels. | | # S1 Pro+ Turn down the volume on all channels. |
| # On the L1 Pro, on input 3 (preferred), turn down the volume - all channels. :If using channels 1 or 2, set the Bass and Treble to 12:00 o'clock and set ToneMatch to Off, and Reverb all the way down.
| | # L1 Pro |
| # Connect the S1 Pro+ Line Out (XLR connection) to L1 Pro Aux Input (input 3). The Aux Input is for line-level sources, and the best match for the line-level output of S1 Pro+. Use and XLR to 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable | | #* Turn down the volume on all channels. |
| <br>[[File:S1 Pro+ to L1 Pro2.jpg|800px]]
| |
| <br>or use an XLR cable with a converter<br>[[File:XLR cable.jpg|300px]][[File:XLR Female to 14 TRS Adapter.jpg|200px]]
| |
| | |
| ==== Levels ====
| |
| # On S1 Pro+, bring up the channel volumes to the desired levels | |
| # On L1 Pro, bring up channel 3 volume to suit your application. Note: This will not necessarily match the same position on the dials as S1 Pro+
| |
| If you connect to channels 1 or 2 instead of 3
| |
| #* Set Bass and Treble at 12:00 o'clock (flat) | | #* Set Bass and Treble at 12:00 o'clock (flat) |
| #* Set Reverb off (see alternate connection below) | | #* Set Reverb off (see alternate connection below) |
| | #* Set ToneMatch to Off |
|
| |
|
| ==== Alternate Connection ==== | | ==== XLR Cable ==== |
| You can use an XLR cable (mic cable) from S1 Pro+ to the L1 Pro channels 1 or 2 (XLR inputs).
| | Use an XLR cable (e.g., microphone cable) to connect the S1 Pro+ Line Out to L1 Pro channel 1 or 2 |
| <!--
| | [[File:S1 Pro+ to L1 Pro2.jpg|800px]] |
| [[File:S1 Pro+ Daisy ConnectionXLR.jpg|800px]] | |
| -->
| |
| XLR Cable
| |
|
| |
|
| [[File:XLR cable.jpg|300px]] | | ==== XLR to 1/4 inch (6.3 mm) Tip-Ring-Sleeve ==== |
| | Use an XLR to 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable |
| | [[File:S1 Pro+ to L1 Pro3.jpg|800px]] |
|
| |
|
| | <br>or use an XLR cable with a converter<br>[[File:XLR cable.jpg|300px]][[File:XLR Female to 14 TRS Adapter.jpg|200px]] |
|
| |
|
| The signal may clip excessively, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB [[Pad]]
| | ==== Levels ==== |
| | | # On S1 Pro+, bring up the channel volumes to the desired levels |
| | | # On L1 Pro, bring up the channel volume to suit your application. Note: This will not necessarily match the same position on the dials as S1 Pro+ |
| [[Pad]]
| |
| | |
| [[File:Pad.jpg|link=Pad|More about Pads]]
| |
|
| |
|
| Click image for more information about Pads
| |
| ---- | | ---- |
| [[Category:S1 Pro+]] | | [[Category:S1 Pro+]] |