T8S to L1 Model II: Difference between revisions

From Bose Portable PA Knowledge
Jump to navigation Jump to search
← Older editNewer edit →
ST (talk | contribs)
Bureaucrats, Interface administrators, Administrators
20,075 edits
VisualWikitext
mNo edit summary
mNo edit summary
Line 16: Line 16:
For each {{Model II}}  
For each {{Model II}}  


=== {{Model II}} Analog Input  ===
{{L1 Model II Analog Input Gain Staging}}
The Analog input is a ¼ inch balanced input jack.
 
[[Image:Model 1S Analog Input Detail.png]]
 
 
==== Analog input trim (volume, or gain) control  ====
Setting the trim level on the Model II Power Stand is a one-time step. Once you have matched the output of the ToneMatch mixer to the input of the {{L1}} you don't need to adjust it again.
 
 
[[Image:Model II Analog Input Trim.png]]
 
# Set the '''Trim''' control on the power stand to the 0 (zero) position.
# Connect the {{T8S}} Main Output to the Analog Input
# Adjust the volume of the {{T8S}} Main Output to the maximum output without distortion. This is probably between 10:00 o'clock and 12:00 o'clock on the Master Output
# While playing the source, increase the '''Trim''' level so that the '''Signal/Clip''' indicator glows green or yellow. This will probably be around 9:00-11:00 o'clock
# If the '''Signal/Clip''' indicator glows red, decrease the '''Trim''' level so that it glows only green or yellow.
 
[[Image:Model II Analog Input Level Green.png|Model 1S Analog Input]]
----
----
[[Category:T8S]]
[[Category:T8S]]
[[Category:Model II]]
[[Category:Model II]]

Revision as of 16:20, 8 March 2019

Connect the T8S to L1 Model II


The output from the T8S ToneMatch mixer is a balanced mono 1/4 inch (6.3 mm) Tip-Ring-Sleeve and the input on the L1 Model II is a balanced mono 1/4 inch (6.3 mm) Tip-Ring-Sleeve so use a cable like this.

1/4" Male TRS to 1/4" Male TRS Cable.

1/4" TRS Balanced Patch Cable (audiopile.net)


Connect the ToneMatch Power Supply to the T8S ToneMatch mixer for power.

Set the L1 Model II Analog Input Trims to about 9:00 o'clock.


Gain Staging

For each L1 Model II


L1 Model II Analog Input

The Analog input is a 1/4 inch (6.3 mm) Tip-Ring-Sleeve balanced input jack.


Analog input trim (volume, or gain) control

Setting the trim level on the Model II Power Stand is a one-time step. Once you have matched the output of the ToneMatch mixer to the input of the L1 you don't need to adjust it again.

T4S/T8S ToneMatch Mixers
  1. Connect the source device Main Output to the L1 Model II Analog Input
  2. Set the Analog Input trim to 9:00 o'clock. Control the volume with the Master Volume on the ToneMatch mixer.
    Model 1S/II Analog Input for T4S/T8S
    If you set the input trim higher, you will have excessive line noise.
  3. If the Signal/Clip indicator glows red, decrease the Trim level so that it glows only green or yellow.
For third-party mixers
  1. Set the Trim control on the power stand to the 0 (zero) position.
  2. Connect the third-party mixer Main Output to the L1 Model II Analog Input
  3. Adjust the volume of the third-party Main Output to the reference or nominal output level.
    • On analog consoles this may be marked as unity or 0 dB.
    • On digital consoles this may be marked as -18 dBFS[1][2]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location[3].
    • Refer to the manual for the third-party for details.
  4. If the Signal/Clip indicator glows red, decrease the Trim level so that it glows only green or yellow.

Model 1S Analog Input

  1. ↑ dBFS
  2. ↑ dBU vs dBFS
  3. ↑ dBFS Analog Levels
Retrieved from "https://boseperformer.com/index.php?title=T8S_to_L1_Model_II&oldid=20564"