Sound Drop Outs at High Volume: Difference between revisions

Line 14:

The second thing we did was redesign the {{L1}} software so that it could "filter out" the effects of momentary crosstalk and not cause the problem. That way future L1's would not have the issue.

=== Intermittent Drop Outs Using the {{T1}} and Model II ===

=== Intermittent Drop Outs Using the {{T1}} and {{Model II}} ===

The user manual states 5 amps or greater, so six amps is a good approximation. For that reason, we recommend only up to two ~~L1 MII’s~~ on a single 15A circuit breaker in the US.

The user manual states 5 amps or greater, so six amps is a good approximation. For that reason, we recommend only up to two {{Model II}}s on a single 15A circuit breaker in the US.

Line 25:

Fixable by tightening the screws in the connector.

This would only happen on one ~~L1 MII~~ at a time. If two dropped out, this is not the issue.

This would only happen on one {{Model II}} at a time. If two dropped out, this is not the issue.

Line 31:

2. Very low, out-of spec, AC power (less than ~105 VAC on a 120V system, or less than around ~215 V on a 230 V system. The manual states 110 and 220 for good measure) coupled with high signal level. This can be caused by a low power source, or one where the outlets are a very long distance from the electrical panel, extra equipment on the same electrical branch, power sags or dropouts, long or multiple extension cords, or small gauge extension cords.

In this case loud music increases the current draw, and the voltage drop over the extension cord will lower the voltage enough to cause a reset of the T1, or the L1 MII base.

In this case loud music increases the current draw, and the voltage drop over the extension cord will lower the voltage enough to cause a reset of the {{T1}}, or the L1 MII base.

If the T1 resets, the LED’s (input trim level, mute LEDs) will turn off. The LCD display will remain blue, but be blank until the unit restarts.

If the {{T1}} resets, the LED’s (input trim level, mute LEDs) will turn off. The LCD display will remain blue, but be blank until the unit restarts.

The L1 MII base can reset but it does not show on the indicators.

@@ Line 14: / Line 14: @@
 The second thing we did was redesign the {{L1}} software so that it could "filter out" the effects of momentary crosstalk and not cause the problem. That way future L1's would not have the issue.
-=== Intermittent Drop Outs Using the {{T1}} and Model II ===
+=== Intermittent Drop Outs Using the {{T1}} and {{Model II}} ===
-The user manual states 5 amps or greater, so six amps is a good approximation. For that reason, we recommend only up to two L1 MII’s on a single 15A circuit breaker in the US.
+The user manual states 5 amps or greater, so six amps is a good approximation. For that reason, we recommend only up to two {{Model II}}s on a single 15A circuit breaker in the US.
@@ Line 25: / Line 25: @@
 Fixable by tightening the screws in the connector.
-This would only happen on one L1 MII at a time. If two dropped out, this is not the issue.
+This would only happen on one {{Model II}} at a time. If two dropped out, this is not the issue.
@@ Line 31: / Line 31: @@
 . Very low, out-of spec, AC power (less than ~105 VAC on a 120V system, or less than around ~215 V on a 230 V system. The manual states 110 and 220 for good measure) coupled with high signal level. This can be caused by a low power source, or one where the outlets are a very long distance from the electrical panel, extra equipment on the same electrical branch, power sags or dropouts, long or multiple extension cords, or small gauge extension cords.
-In this case loud music increases the current draw, and the voltage drop over the extension cord will lower the voltage enough to cause a reset of the T1, or the L1 MII base.
+In this case loud music increases the current draw, and the voltage drop over the extension cord will lower the voltage enough to cause a reset of the {{T1}}, or the L1 MII base.
-If the T1 resets, the LED’s (input trim level, mute LEDs) will turn off. The LCD display will remain blue, but be blank until the unit restarts.
+If the {{T1}} resets, the LED’s (input trim level, mute LEDs) will turn off. The LCD display will remain blue, but be blank until the unit restarts.
 The L1 MII base can reset but it does not show on the indicators.