Securing the T1® to the Microphone Stand Bracket: Difference between revisions
Jump to navigation
Jump to search
mNo edit summary |
mNo edit summary |
||
| Line 17: | Line 17: | ||
#I insert all the other cables into the T1® before I put it on the bracket. I do it this way because I have all my cables strapped to the microphone stand (I don't take them off between gigs). So there's no hanging stress from those either. | #I insert all the other cables into the T1® before I put it on the bracket. I do it this way because I have all my cables strapped to the microphone stand (I don't take them off between gigs). So there's no hanging stress from those either. | ||
# Finally, I set the T1® on top of the bracket. | # Finally, I set the T1® on top of the bracket. | ||
<ref>Original discussion about [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/9370021626?r=3300035626#3300035626 using the T1® Microphone stand adapter]</ref> | |||
[[Image:T1 Strapped 02.png]] | [[Image:T1 Strapped 02.png]] | ||
In the picture above, I am using all the inputs and the cables are heavy. But since I have all the cables secured by a velcro strap, there's no chance that the T1® will come off the microphone stand bracket. | In the picture above, I am using all the inputs and the cables are heavy. But since I have all the cables secured by a velcro strap, there's no chance that the T1® will come off the microphone stand bracket. | ||
| Line 37: | Line 40: | ||
Comments? Please join the [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/9540096066 discussion on the Bose L1® Forum] | Comments? Please join the [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/9540096066 discussion on the Bose L1® Forum] | ||
<noinclude> | |||
---- | |||
<references /> | |||
</noinclude> | |||
---- | ---- | ||
[[Category:T1]] | [[Category:T1]] | ||
Revision as of 15:10, 24 January 2014
- The bracket that sits parallel to the floor has a bevel on the top. The bevel should run down, facing you. If the bevel runs down away from you, the bracket is upside down and the T1 ToneMatch® Audio Engine will not sit properly on top of it.
- correct - bevel running down, facing you
- incorrect (upside down)- bevel on opposite side, away from you
This is how I secure the T1® to the T1® Microphone Stand Bracket
- There is a velcro strap on the black ToneMatch cable.
- I use the velcro to secure the ToneMatch cable to the microphone stand just above the Microphone Stand Adapter (the thing that clamps around the mic stand).
- Then I insert the ToneMatch cable into the T1®. It locks into place.
- At this point, most people would put the T1® on the bracket and attach the other cables.
- I insert all the other cables into the T1® before I put it on the bracket. I do it this way because I have all my cables strapped to the microphone stand (I don't take them off between gigs). So there's no hanging stress from those either.
- Finally, I set the T1® on top of the bracket.
In the picture above, I am using all the inputs and the cables are heavy. But since I have all the cables secured by a velcro strap, there's no chance that the T1® will come off the microphone stand bracket.
The white cable is a network cable (Cat-5) instead of the ToneMatch® cable
— source
— source
Comments? Please join the discussion on the Bose L1® Forum
- ↑ Original discussion about using the T1® Microphone stand adapter