Denon DN-MC6000: Difference between revisions

Line 1:

Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact.

See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10]

See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)]

[[Image:Denon DN-MC6000 Output.png]]

Running mono, set the output to MONO above and connect to the ~~L1®~~ Analog input ~~with~~ a cable like this:

Running mono, set the output to MONO above and connect to the [[L1%C2%AE_Model_II#Analog_Input Model II Analog input]] or [[L1%C2%AE_Model_1S#Analog_Input Model 1S Analog input]]

[[http://toonz.ca/bose/wiki/images/b/b6/Model_1S_Analog_Input_Detail.png]]

With a cable like this:

[[Image:XLR to TRS mp106.jpg]]

[http://www.audiopile.net/products/Mic_Instr_Cables/MP_Adaptor_Cbls/MP-105/MP-105_cutsheet.shtml Source: Audiopile.net]

Technical Description:

The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment.

The Female XLR end is wired through to the 1/4" Male TRS end as follows:

* Pin One FXLR to Sleeve of MTRS

* Pin Two FXLR to Tip of MTRS

* Pin Three FXLR to Ring of MTRS

The 1/4" MTRS end is an EWI model P292S-BKG

The FXLR end is an EWI model ES3FB-GDP

The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors.

@@ Line 1: / Line 1: @@
 Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact.
-See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10]
+See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)]
 [[Image:Denon DN-MC6000 Output.png]]
-Running mono, set the output to MONO above and connect to the L1® Analog input with a cable like this:
+Running mono, set the output to MONO above and connect to the [[L1%C2%AE_Model_II#Analog_Input Model II  Analog input]] or  [[L1%C2%AE_Model_1S#Analog_Input Model 1S Analog input]]
+[[http://toonz.ca/bose/wiki/images/b/b6/Model_1S_Analog_Input_Detail.png]]
+With a cable like this:
 [[Image:XLR to TRS mp106.jpg]]
 [http://www.audiopile.net/products/Mic_Instr_Cables/MP_Adaptor_Cbls/MP-105/MP-105_cutsheet.shtml Source: Audiopile.net]
+Technical Description:
+The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS.  This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment.
+The Female XLR end is wired through to the 1/4" Male TRS end as follows:
+*    Pin One FXLR to Sleeve of MTRS
+*    Pin Two FXLR to Tip of MTRS
+*    Pin Three FXLR to Ring of MTRS
+The 1/4" MTRS end is an EWI model P292S-BKG
+The FXLR end is an EWI model ES3FB-GDP
+The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors.