|
|
| Line 109: |
Line 109: |
|
| |
|
| == Power Stand Input Setting == | | == Power Stand Input Setting == |
| Here is a quick look at how you can connect your {{T1}} to a {{Classic}} or {{Model I}}
| |
|
| |
|
| [[Image:T1toPS1.png]]
| | {{T1 to Model I or Classic}} |
| | |
| Notes:
| |
| | |
| {{T1 icon}}{{Model I icon}}{{Classic icon}} When using the Classic or Model I <ref>Hilmar-at-Bose talks about setting inputs [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=2991039944#2991039944]</ref> The T1 has more input capability then the Model 1,s so you should be able to use the T1 as the only control for your system. We have a recommended trim setting for connecting the T1 to a {{Model I nl}} input Ch 3 or Ch 4 | |
| | |
| Note: New recommendation is '''3''' see below.
| |
| | |
| With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.
| |
| | |
| The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.
| |
| | |
| === Input setting recommendation now '''3''' ===
| |
| <section begin=InputSettingNow3 />
| |
| MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.
| |
| | |
| For these conditions:
| |
| {{Classic icon}}{{Model I icon}}
| |
| * {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4
| |
| * Balanced OR Unbalanced 1/4" cable
| |
| * {{Remote}} unplugged, OR, master volume on {{Remote}} at 12 o clock
| |
| * Proper gain staging required on the T1® itself
| |
| | |
| I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.
| |
| | |
| This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}.
| |
| | |
| If you are using the {{Remote}} on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the {{Remote}} master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.
| |
| <section end=InputSettingNow3 />
| |
| | |
| Hopefully this is helpful - please ask away with any questions for clarification.
| |
| | |
| MikeZ
| |
| | |
| | |
| === Connection to {{Model I}} / {{Classic}} with Remote ===
| |
| If you want to use the PS1 Power Stand Channels 1 or 2 or 4, then you will want to connect the R1 Remote to the PS1 Power Stand.
| |
| | |
| [[Image:T1toPS1withRemote.png]]
| |
| | |
| | |
| <!--
| |
| === Connections to a Model I or Classic ===
| |
| MikeZ-at-Bose gave us some more insight<ref>MikeZ-at-Bose talking about [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/100102183?r=5671030415#5671030415 T1™ to Model I Connections]</ref>
| |
| | |
| Without getting too deep into technical stuff, with regards to the T1 the two ways to interface with a {{Model I}} are:
| |
| | |
| 1.) The way we generally recommend - 1/4" out from the T1 into Ch 3/4 with the Level at '''4'''.
| |
| | |
| 2.) 1/4" balanced {{TRS}} from the T1 to XLR input of Ch 1/2. Of course this requires a TRS to XLR cable which most folks don't have lying around - but is a common studio connector available at GC etc.
| |
| | |
| Both ways are equal as long as your distance from the model I is less than 25 or 30 feet. Longer than that I would lean toward option #2.Method #1 allows you not to use a preset Channel on the model I.
| |
| | |
| -->
| |
| | |
| ----
| |
| | |
| Excerpt from the {{T1}} Manual - page 20 - Note: this recommended input setting is now '''3'''. See the note above.
| |
| | |
| [[Image:T12ModelI.png]]
| |
| | |
| == ToneMatch® Port==
| |
| | |
| {{:ToneMatch® Port}}
| |
|
| |
|
| == Aux Output == | | == Aux Output == |