T1 ToneMatch® Audio Engine: Difference between revisions

Line 127:

=== Input setting recommendation now '''3''' ===

MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the Model I or Classic Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.

MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.

For these conditions:

*{{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4

* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4

*~~balanced~~ OR ~~unbalanced~~ 1/4" cable

* Balanced OR Unbalanced 1/4" cable

*~~remote~~ unplugged, OR, master volume on ~~remote~~ at 12 o clock

* [[R1 Remote|Remote]] unplugged, OR, master volume on [[R1 Remote|Remote]] at 12 o clock

*~~proper~~ gain staging required on the T1® itself

* Proper gain staging required on the T1® itself

I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.

This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the ~~digital ethercon~~ input on a {{Model II}}.

This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}.

If you are using the remote on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the remote master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.

@@ Line 127: / Line 127: @@
 === Input setting recommendation now '''3'''  ===
 <section begin=InputSettingNow3 />
-MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the Model I or Classic Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.
+MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.
 For these conditions:
 {{Classic icon}}{{Model I icon}}
-*{{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4
+* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4
-*balanced OR unbalanced 1/4" cable
+* Balanced OR Unbalanced 1/4" cable
-*remote unplugged, OR, master volume on remote at 12 o clock
+* [[R1 Remote|Remote]] unplugged, OR, master volume on [[R1 Remote|Remote]] at 12 o clock
-*proper gain staging required on the T1® itself
+* Proper gain staging required on the T1® itself
 I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.
-This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the digital ethercon input on a {{Model II}}.
+This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}.
 If you are using the remote on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the remote master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.