T1 ToneMatch® Audio Engine / Para EQ: Difference between revisions

Line 15:

imagine that we are increasing the Width parameter.

In the plots below the centre point (lowest representing -6dB ) is the Frequency that you select with the middle button, in this case 165 Hz (E3, not shown in the Simulator). The tick marks on the X-axis are roughly 1 octave~~. I have deliberately omitted actual frequencies because I wanted to give you a sense of relative differences rather than suggest that this is what is actually happening~~.

In the plots below the centre point (lowest representing -6dB ) is the Frequency that you select with the middle button, in this case 165 Hz (E3, not shown in the Simulator). The tick marks on the X-axis are roughly one octave.

The plots below suggest the widening range of notes that will be affected by the Level (-6 dB) as we go increase the Width. The plots point down because we are applying a *negative* level. The depth of the plot (distance down) would vary up and down as we changed the Level.

The plots below suggest the widening range of notes that will be affected by the Level (-6 dB) as we go increase the Width. The plots point down because we are applying a ''negative'' level. The depth of the plot (distance down) would vary up and down as we changed the Level. I have kept these constant so we can focus on the Width parameter.

The following are extremely rough approximations. For anyone reading - there is nothing scientific about these plots. The appearance suggests a level of precision that is way beyond what I did to create these images. (Normal distribution curve, manipulated the standard deviation). Just go for the rough visual impression. Thanks!

Line 50:

|[[Image:T1ParaEQWidth-50.png|thumb|Width = 5.0 Octaves (2.50 Octaves on either side of the Freq)]]

|}

The discussion continues here: [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/5011087105?r=5011087105#5011087105 T1 Newbie Questions/Solutions]

Related article [[T1 ToneMatch™ Audio Engine/Tips & Tricks]]

----

[[Category:T1]]

</noinclude>

@@ Line 15: / Line 15: @@
 imagine that we are increasing the Width parameter.
-In the plots below the centre point (lowest representing -6dB ) is the Frequency that you select with the middle button, in this case 165 Hz (E3, not shown in the Simulator). The tick marks on the X-axis are roughly 1 octave. I have deliberately omitted actual frequencies because I wanted to give you a sense of relative differences rather than suggest that this is what is actually happening.
+In the plots below the centre point (lowest representing -6dB ) is the Frequency that you select with the middle button, in this case 165 Hz (E3, not shown in the Simulator). The tick marks on the X-axis are roughly one octave.
-The plots below suggest the widening range of notes that will be affected by the Level (-6 dB) as we go increase the Width. The plots point down because we are applying a *negative* level. The depth of the plot (distance down) would vary up and down as we changed the Level.
+The plots below suggest the widening range of notes that will be affected by the Level (-6 dB) as we go increase the Width. The plots point down because we are applying a ''negative'' level. The depth of the plot (distance down) would vary up and down as we changed the Level. I have kept these constant so we can focus on the Width parameter.
 The following are extremely rough approximations. For anyone reading - there is nothing scientific about these plots. The appearance suggests a level of precision that is way beyond what I did to create these images. (Normal distribution curve, manipulated the standard deviation). Just go for the rough visual impression. Thanks!
@@ Line 50: / Line 50: @@
 |[[Image:T1ParaEQWidth-50.png|thumb|Width = 5.0 Octaves (2.50 Octaves on either side of the Freq)]]
 |}
+The discussion continues here: [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/5011087105?r=5011087105#5011087105 T1 Newbie Questions/Solutions]
+Related article [[T1 ToneMatch™ Audio Engine/Tips & Tricks]]
 <noinclude>
+----
 [[Category:T1]]
 </noinclude>