T1 ToneMatch® Audio Engine to F1 System: Difference between revisions

Line 28:

To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input.

To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input. Use a ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve cable.

[[Image:TrsMtrsM.png|600px]]

[[Image:T1 to F1 Model 812 Mono.png|600px]]

Line 37:

Line 38:

'''For best results use a balanced connection

; ¼ Inch Tip-Ring-Sleeve ~~(balanced)~~ to ¼ Inch Tip-Ring-Sleeve ~~(balanced)~~'''

; ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve'''

A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.

Line 47:

Line 48:

=== XLR connection from F1 Model 812 Line Out to second F1 Model 812 Channel 1 ===

Use an ordinary microphone cable to connect the first F1 Model 812 to the second one.

=== General settings ===

* Turn the volume off for any channels you are not using. In the diagram above, you would turn off channel 2 for both F1 systems.

* On the first F1, set the Level Control to MIC

* On the second F1, set the Level Control to LINE

* Set the volume on the second F1 to 10:00 o'clock. Then adjust the volume on the second F1 to match the output of the first F1 (if necessary). It's likely, you will have the volume on the second F1 lower than the first. That is normal.

** Note: The volume control on the first F1 will raise and lower the volume on the second F1

=== Using an F1 Subwoofer ===

@@ Line 28: / Line 28: @@
-To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input.
+To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input. Use a  ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve cable.
+[[Image:TrsMtrsM.png|600px]]
 [[Image:T1 to F1 Model 812 Mono.png|600px]]
@@ Line 37: / Line 38: @@
 '''For best results use a balanced connection
-; ¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)'''
+; ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve'''
 A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.
@@ Line 47: / Line 48: @@
 === XLR connection from F1 Model 812 Line Out to second F1 Model 812 Channel 1 ===
 Use an ordinary microphone cable to connect the first F1 Model 812 to the second one.
+=== General settings ===
+* Turn the volume off for any channels you are not using. In the diagram above, you would turn off channel 2 for both F1 systems.
+* On the first F1, set the Level Control to MIC
+* On the second F1, set the Level Control to LINE
+* Set the volume on the second F1 to 10:00 o'clock. Then adjust the volume on the second F1 to match the output of the first F1 (if necessary). It's likely, you will have the volume on the second F1 lower than the first. That is normal.
+** Note: The volume control on the first F1 will raise and lower the volume on the second F1
 === Using an F1 Subwoofer ===