T1 ToneMatch® Audio Engine to F1 System: Difference between revisions

Line 6:

Please post comments or questions in [http://bose.infopop.cc/eve/forums/a/tpc/f/6120043776/m/5000004086 this discussion in the Bose Forum]. Thank you.

~~Note: If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the T1® to the F1 Model 812 instead of the F1 Subwoofer.~~

Connecting the T1® to the F1 Model 812 Channel 1, you can control the relative loudness of the F1 Stack (F1 Model 812 with F1 Subwoofer) to your L1® with the Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1. You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.

;Balanced connections.

Line 16:

Line 12:

</td>

</tr></table>

== {{T1}} Considerations ==

If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the T1® to the F1 Model 812 instead of the F1 Subwoofer.

Connecting the T1® to the F1 Model 812 Channel 1, you can control the relative loudness of the F1 Stack (F1 Model 812 with F1 Subwoofer) to your L1® with the Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1. You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.

=== T1® Master Volume ===

If you want to run the T1® full output without it being affected by the T1® Master Volume see [[T1® Audio Engine / Master Output Pre / Post]]

== Mono Connection ==

This describes how you can run an {{Model II}} or {{Model 1S}} with a {{T1}} and run one or more {{F1}}s at the same time.

@@ Line 6: / Line 6: @@
 Please post comments or questions in  [http://bose.infopop.cc/eve/forums/a/tpc/f/6120043776/m/5000004086 this discussion in the Bose Forum]. Thank you.
-Note: If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the T1® to the F1 Model 812 instead of the F1 Subwoofer.
-Connecting the T1® to the F1 Model 812 Channel&nbsp;1, you can control the relative loudness of the  F1 Stack (F1 Model 812 with F1 Subwoofer) to your L1®  with the Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1.  You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.
 ;Balanced connections.
@@ Line 16: / Line 12: @@
 </td>
 </tr></table>
+== {{T1}} Considerations ==
+If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the T1® to the F1 Model 812 instead of the F1 Subwoofer.
+Connecting the T1® to the F1 Model 812 Channel&nbsp;1, you can control the relative loudness of the  F1 Stack (F1 Model 812 with F1 Subwoofer) to your L1®  with the Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1.  You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.
+=== T1® Master Volume ===
+If you want to run the T1® full output without it being affected by the T1® Master Volume see [[T1® Audio Engine / Master Output Pre / Post]]
 == Mono Connection ==
 This describes how you can run an {{Model II}} or {{Model 1S}} with a {{T1}} and run one or more {{F1}}s at the same time.