Template:T1 to Model I or Classic: Difference between revisions

Line 50:

[[Image:T12ModelI.png]]

With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.

The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.

=== Input setting recommendation now '''3''' ===

MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.

For these conditions:

* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4

* Balanced OR Unbalanced 1/4" cable

* {{Remote}} unplugged, OR, master volume on {{Remote}} at 12 o clock

* Proper gain staging required on the T1® itself

I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.

This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}.

If you are using the {{Remote}} on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the {{Remote}} master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.

Hopefully this is helpful - please ask away with any questions for clarification.

MikeZ

@@ Line 50: / Line 50: @@
 [[Image:T12ModelI.png]]
+With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.
+The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.
+=== Input setting recommendation now '''3'''  ===
+<section begin=InputSettingNow3 />
+MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.
+For these conditions:
+{{Classic icon}}{{Model I icon}}
+* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4
+* Balanced OR Unbalanced 1/4" cable
+* {{Remote}} unplugged, OR, master volume on {{Remote}} at 12 o clock
+* Proper gain staging required on the T1® itself
+I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.
+This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}.
+If you are using the {{Remote}} on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the {{Remote}} master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.
+<section end=InputSettingNow3 />
+Hopefully this is helpful - please ask away with any questions for clarification.
+MikeZ