L1 Cylindrical Radiator® loudspeaker: Difference between revisions

Line 37:

== Lower Half Only? ==

=== {{Classic}}===

Q: Can I run with only the lower section of the {{L1 CR}}?

A: From a technical standpoint it is safe to operate the system with only the lower L1, however the spatial and spectral performance of will be greatly reduced, so this has only a very limited application.

A: From a technical standpoint it is safe to operate the system with only the lower section of the {{PAGENAME}} , however the spatial and spectral performance of will be greatly reduced, so this has only a very limited application.

- Hilmar-at-Bose<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/4806048934/m/177104427?r=9641062702#9641062702 Hilmar-at-Bose talks about using the lower half (only) of the ~~L1™~~ Cylindrical Radiator in the Bose® Musicians Community Message Boards]</ref>

- Hilmar-at-Bose<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/4806048934/m/177104427?r=9641062702#9641062702 Hilmar-at-Bose talks about using the lower half (only) of the {{L1r}} Cylindrical Radiator in the Bose® Musicians Community Message Boards]</ref>

=== {{Model I nl}} {{Model II nl}}===

Note: Both sections of the Cylindrical Radiator® are powered by the same internal amplifier. Removing the top section changes the impedance presented to the amplifier. This will not harm the amplifier, but this is not recommended.

=== Correcting the Tone ===

Try inserting a ¼ inch connector in the Bass Line Out of the Power Stand. This will cause the internal logic to reduce the Bass output, and this should give you a better overall tonal balance when running with only one section of the {{PAGENAME}}.

== Tilting the {{L1}} ==

@@ Line 37: / Line 37: @@
 == Lower Half Only? ==
+=== {{Classic}}===
+{{Classic icon}}
 Q: Can I run with only the lower section of the {{L1 CR}}?
-A: From a technical standpoint it is safe to operate the system with only the lower L1, however the spatial and spectral performance of will be greatly reduced, so this has only a very limited application.
+A: From a technical standpoint it is safe to operate the system with only the lower section of the {{PAGENAME}} , however the spatial and spectral performance of will be greatly reduced, so this has only a very limited application.
-- Hilmar-at-Bose<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/4806048934/m/177104427?r=9641062702#9641062702 Hilmar-at-Bose talks about using the lower half (only) of the L1™ Cylindrical Radiator in the Bose® Musicians Community Message Boards]</ref>
+- Hilmar-at-Bose<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/4806048934/m/177104427?r=9641062702#9641062702 Hilmar-at-Bose talks about using the lower half (only) of the {{L1r}} Cylindrical Radiator in the Bose® Musicians Community Message Boards]</ref>
+=== {{Model I nl}} {{Model II nl}}===
+{{Model I icon}}{{Model II icon}}
+Note: Both sections of the Cylindrical Radiator® are powered by the same internal amplifier. Removing the top section changes the impedance presented to the amplifier. This will not harm the amplifier, but this is not recommended.
+=== Correcting the Tone ===
+Try inserting a &frac14; inch connector in the Bass Line Out of the Power Stand. This will cause the internal logic to reduce the Bass output, and this should give you a better overall tonal balance when running with only one section of the {{PAGENAME}}.
+<!--TODO find a reference for &frac14; inch plug in the Bass Line Out - MikeZ said it, just have to find the reference -->
 == Tilting the {{L1}} ==