L1® PackLite® A1 Amplifier / FAQ: Difference between revisions

(7 intermediate revisions by the same user not shown)

Line 39:

The A1 is designed for 4-ohm loudspeaker loads capable of 250W RMS. The MB4, MB24 and

802® are rated at an impedance of 8-ohms nominal. Coupled with higher power requirements at their load rating, the A1 is slightly underpowered for use with those loudspeakers. We recommend the Bose® 1600 or Bose 1800 amplifier together with the Panaray® controller to properly drive those loudspeakers. For more information, please visit [http://www.pro.bose.com/ ~~<font color="#0000FF">===~~ www.pro.Bose.com] ~~=== </font>~~.

802® are rated at an impedance of 8-ohms nominal. Coupled with higher power requirements at their load rating, the A1 is slightly underpowered for use with those loudspeakers. We recommend the Bose® 1600 or Bose 1800 amplifier together with the Panaray® controller to properly drive those loudspeakers.

For more information, please visit [http://www.pro.bose.com/ http://www.pro.Bose.com].

=== Can I use two B1 bass modules with the A1 amplifier without the power stand? ===

Line 189:

Line 190:

==== B1 cable 5.5" (1.7m)====

Heavy-duty 4-pin cable connects B1 bass modules to L1™ Model II or II power stands. Longer B1 cables may be obtained from [~~file~~://~~C:\Documents_and_Settings\AP17102\Local_Settings\Application_Data\Microsoft\Word\~~www.audiopile.net www.audiopile.net].

Heavy-duty 4-pin cable connects B1 bass modules to L1™ Model II or II power stands. Longer B1 cables may be obtained from [http://www.audiopile.net www.audiopile.net].

==== Heavy-duty B1 gig bag====

Line 295:

Line 296:

=== What if the A1 amplifier fails during a performance? ===

The A1 amplifier is built for road use and is tested under the most stringent conditions. To prevent damage, the amplifier is protected against overheating, short-circuits and over-current conditions. The power LED will turn red when there is a problem and will return to normal operating mode when ~~thefault~~ condition has been removed. If used with a power stand and two B1s, the bass level would drop 6dB upon shutdown.

The A1 amplifier is built for road use and is tested under the most stringent conditions. To prevent damage, the amplifier is protected against overheating, short-circuits and over-current conditions. The power LED will turn red when there is a problem and will return to normal operating mode when the fault condition has been removed. If used with a power stand and two B1s, the bass level would drop 6dB upon shutdown.

=== What is the warranty coverage on my A1? ===

The A1 comes with a one-year limited warranty in the U.S. and Canada. Outside the U.S. and Canada, check with your local Bose® representative.

The A1 comes with a [strike]one-year[/strike] two-year limited warranty in the U.S. and Canada. Outside the U.S. and Canada, check with your local Bose® representative. See [[Warranty_Information]] for current information.

=== Is there an available hard case for the A1 amplifier? ===

@@ Line 39: / Line 39: @@
 The A1 is designed for 4-ohm loudspeaker loads capable of 250W RMS. The MB4, MB24 and
-® are rated at an impedance of 8-ohms nominal. Coupled with higher power requirements at their load rating, the A1 is slightly underpowered for use with those loudspeakers. We recommend the Bose® 1600 or Bose 1800 amplifier together with the Panaray® controller to properly drive those loudspeakers. For more information, please visit [http://www.pro.bose.com/ <font color="#0000FF">=== www.pro.Bose.com] === </font>.
+® are rated at an impedance of 8-ohms nominal. Coupled with higher power requirements at their load rating, the A1 is slightly underpowered for use with those loudspeakers. We recommend the Bose® 1600 or Bose 1800 amplifier together with the Panaray® controller to properly drive those loudspeakers.
+For more information, please visit [http://www.pro.bose.com/ http://www.pro.Bose.com].
 === Can I use two B1 bass modules with the A1 amplifier without the power stand? ===
@@ Line 189: / Line 190: @@
 ==== B1 cable 5.5" (1.7m)====
-Heavy-duty 4-pin cable connects B1 bass modules to L1™ Model II or II power stands. Longer B1 cables may be obtained from [file://C:\Documents_and_Settings\AP17102\Local_Settings\Application_Data\Microsoft\Word\www.audiopile.net www.audiopile.net].
+Heavy-duty 4-pin cable connects B1 bass modules to L1™ Model II or II power stands. Longer B1 cables may be obtained from [http://www.audiopile.net www.audiopile.net].
 ==== Heavy-duty B1 gig bag====
@@ Line 295: / Line 296: @@
 === What if the A1 amplifier fails during a performance? ===
-The A1 amplifier is built for road use and is tested under the most stringent conditions. To prevent damage, the amplifier is protected against overheating, short-circuits and over-current conditions. The power LED will turn red when there is a problem and will return to normal operating mode when thefault condition has been removed. If used with a power stand and two B1s, the bass level would drop 6dB upon shutdown.
+The A1 amplifier is built for road use and is tested under the most stringent conditions. To prevent damage, the amplifier is protected against overheating, short-circuits and over-current conditions. The power LED will turn red when there is a problem and will return to normal operating mode when the fault condition has been removed. If used with a power stand and two B1s, the bass level would drop 6dB upon shutdown.
 === What is the warranty coverage on my A1? ===
-The A1 comes with a one-year limited warranty in the U.S. and Canada. Outside the U.S. and Canada, check with your local Bose® representative.
+The A1 comes with a [strike]one-year[/strike] two-year limited warranty in the U.S. and Canada. Outside the U.S. and Canada, check with your local Bose® representative. See [[Warranty_Information]] for current information.
 === Is there an available hard case for the A1 amplifier? ===