T1 Compatibility With L1 Pro Systems: Difference between revisions

(7 intermediate revisions by the same user not shown)

Line 1:

;Question: Can I use the {{T1}} with the {{L1PS}}s?

[[File:T1 to L1 Pro.jpg|~~600px~~|right]]

[[File:T1 to L1 Pro.jpg|400px|right]]

;Answer: Yes using two connections

# ToneMatch port supplies power to the {{T1}}

# An analog cable from the {{T1}} Master Output to one of the L1 Pro channels (preferably channel 3)

:; Required

# ToneMatch cable (these were included with the {{T1}}), or network cable (CAT5/6/7) up to 50 feet<br>OR you can use a ToneMatch Power Supply instead of connecting to the {{L1PS}} for power.

# {{14TRS}} cable. This is the preferred cable for best results, but you can use a {{14TS}} cable. You'll be more vulnerable to line noise but if your cable length is less than 20-25 feet, this can work.

;Connections and initial settings

# On the L1 Pro, turn off the system and turn down the volume on all channels

# On the {{T1}}, turn the Master Volume off

# Power: Connect the {{L1P}} ToneMatch port to the {{T1}} ToneMatch port using the ToneMatch cable

# Audio: Connect the {{T1}} Master Output to the {{L1P}} channel 3 unless you are already using it for Bluetooth or another sound source. This leaves channels 1 and 2 open for other sound sources.

#* On channel 3, set Treble and Bass at 12:00 (flat)

#* If you connect to {{L1P}} channel 1 or channel 2

#** On the {{L1P}} channel:

Line 29:

Line 34:

#* Turn up the Master volume to the desired level

; Why do you need two connections?

Regarding T1 compatibility with the L1 Pro systems: The architecture of the T1 ToneMatch differs from that of the T4S and T8S ToneMatch mixers and is not compatible with the L1 Pro’s S/PDIF audio architecture.

@@ Line 1: / Line 1: @@
 ;Question: Can I use the {{T1}} with the {{L1PS}}s?
-[[File:T1 to L1 Pro.jpg|600px|right]]
+[[File:T1 to L1 Pro.jpg|400px|right]]
 ;Answer: Yes using two connections
+# ToneMatch port supplies power to the {{T1}}
+# An analog cable from the {{T1}} Master Output to one of the L1 Pro channels (preferably channel 3)
+:; Required
+# ToneMatch cable (these were included with the {{T1}}), or network cable (CAT5/6/7) up to 50 feet<br>OR you can use a ToneMatch Power Supply instead of connecting to the {{L1PS}} for power.
+# {{14TRS}} cable. This is the preferred cable for best results, but you can use a {{14TS}} cable. You'll be more vulnerable to line noise but if your cable length is less than 20-25 feet, this can work.
 ;Connections and initial settings
 # On the L1 Pro, turn off the system and turn down the volume on all channels
 # On the {{T1}}, turn the Master Volume off
 # Power: Connect the {{L1P}} ToneMatch port to the {{T1}} ToneMatch port using the ToneMatch cable
 # Audio: Connect the {{T1}} Master Output to the {{L1P}} channel 3 unless you are already using it for Bluetooth or another sound source. This leaves channels 1 and 2 open for other sound sources.
+#* On channel 3, set Treble and Bass at 12:00 (flat)
 #* If you connect to {{L1P}} channel 1 or channel 2
 #** On the {{L1P}} channel:
@@ Line 29: / Line 34: @@
 #* Turn up the Master volume to the desired level
+; Why do you need two connections?
 <blockquote>
 Regarding T1 compatibility with the L1 Pro systems: The architecture of the T1 ToneMatch differs from that of the T4S and T8S ToneMatch mixers and is not compatible with the L1 Pro’s S/PDIF audio architecture.