Template:T8S to L1 Pro: Difference between revisions

(14 intermediate revisions by the same user not shown)

Line 1:

=== T8S to Single {{L1P}}===

There is a single ToneMatch port on the {{T8S}}. You can use this

* To connect to an {{L1P}} ToneMatch Port using a [[ToneMatch Cable]] [[File:ToneMatch Cable.jpg|thumb|ToneMatch cable|link=ToneMatch_Cable]] or Network Cable [[File:Cat5.jpg|thumb|Network cable|link=ToneMatch_Cable#CAT5_or_CAT6_or_CAT7_or_CAT8_cable]]

** Note: The maximum length of the network cable is 50 feet.

** Note: This is the mixer LEFT output. Anything panned hard RIGHT will not be heard.

All of the Analog outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) still function while using the ToneMatch Port.

Line 7:

Line 9:

[[File:T8S ToneMatch Port to L1 Pro32.jpg]]

To run stereo, connect the second powered loudspeaker to one of the {{T8S}} RIGHT Outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) to the second L1 Pro Input three. ~~DO NOT USE~~ an XLR to XLR cable. ~~The output of~~ the ~~{{T8S}} outputs is too hot for~~ the ~~L1 Pro XLR inputs~~.

To run stereo, connect the second powered loudspeaker to one of the {{T8S}} RIGHT Outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) to the second L1 Pro Input three. You can use an XLR to XLR cable. However, you may need to turn down the channel volume level to match the input sensitivity to the signal level.

[[File:XLR Female to TRS.jpg]]

[[File:XLR Female to TRS.jpg|200px]]

Line 16:

Line 18:

* ToneMatch port on the {{T8S}} to [[ToneMatch Power Supply]] for power and use the Analog Outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) to the L1 Pro Input three. DO NOT USE an XLR to XLR cable. The output of the {{T8S}} outputs is too hot for the L1 Pro XLR inputs.

[[File:XLR Female to TRS.jpg]]

[[File:XLR Female to TRS.jpg|200px]]

=== {{T8S}} to Two {{L1P}} Stereo ===

==== ToneMatch Port and 1/4 inch (6.3 mm) ====

[[File:T8S ToneMatch Port to L1 Pro32 x2.jpg|800px]]

==== 1/4 inch (6.3 mm) Tip-Ring-Sleeve ====

==== XLR ====

#Connect your audio sources (instruments or microphones) to the inputs on the ToneMatch mixer

#Connect the T8S power supply from the Power port of the T8S to a power outlet

#Connect an XLR cable from the Main Out R port of the mixer to the right-side L1 system

#*Tip: If connecting to channels 1 or 2 on the second system, set the ToneMatch selector for that channel to OFF

#Connect an XLR cable from the Main Out L port of the mixer to the left-side L1 system.

#*Tip: If connecting to channels 1 or 2 on the second system, set the ToneMatch selector for that channel to OFF.

<ref>[https://support.bose.com/s/display-articles?productId=01t8c00000OydHYAAZ&articleId=ka08c000001gBWrAAM&language=en_US Bose Support Article]</ref>

=== {{T8S}} to Two Single {{L1P}} Mono Daisy Chain ===

Connect the {{T8S}} to the first {{L1P}}

[[File:T8S ToneMatch Port to L1 Pro32.jpg|400px]]

Then connect the output of the first {{L1P}} to the second {{L1P}}

Line 25:

Line 49:

[[Category:T8S]]

[[Category:L1 Pro]]

[[Category:Connections]]

@@ Line 1: / Line 1: @@
-<noinclude></noinclude>
+<noinclude>__TOC__</noinclude>
+=== T8S to Single {{L1P}}===
 There is a single ToneMatch port on the {{T8S}}. You can use this
 * To connect to an {{L1P}} ToneMatch Port using a [[ToneMatch Cable]] [[File:ToneMatch Cable.jpg|thumb|ToneMatch cable|link=ToneMatch_Cable]] or Network Cable [[File:Cat5.jpg|thumb|Network cable|link=ToneMatch_Cable#CAT5_or_CAT6_or_CAT7_or_CAT8_cable]]
+** Note: The maximum length of the network cable is 50 feet.
 ** Note: This is the mixer LEFT output. Anything panned hard RIGHT will not be heard.
 All of the Analog outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) still function while using the ToneMatch Port.
@@ Line 7: / Line 9: @@
 [[File:T8S ToneMatch Port to L1 Pro32.jpg]]
-To run stereo, connect the second powered loudspeaker to one of the {{T8S}} RIGHT Outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) to the second L1 Pro Input three. DO NOT USE an XLR to XLR cable. The output of the {{T8S}} outputs is too hot for the L1 Pro XLR inputs.
+To run stereo, connect the second powered loudspeaker to one of the {{T8S}} RIGHT Outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) to the second L1 Pro Input three. You can use an XLR to XLR cable. However, you may need to turn down the channel volume level to match the input sensitivity to the signal level.
-[[File:XLR Female to TRS.jpg]]
+[[File:XLR Female to TRS.jpg|200px]]
@@ Line 16: / Line 18: @@
 * ToneMatch port on the {{T8S}} to [[ToneMatch Power Supply]] for power and use the Analog Outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve) to the L1 Pro Input three. DO NOT USE an XLR to XLR cable. The output of the {{T8S}} outputs is too hot for the L1 Pro XLR inputs.
-[[File:XLR Female to TRS.jpg]]
+[[File:XLR Female to TRS.jpg|200px]]
+=== {{T8S}} to Two {{L1P}} Stereo ===
+==== ToneMatch Port and 1/4 inch (6.3 mm) ====
+[[File:T8S ToneMatch Port to L1 Pro32 x2.jpg|800px]]
+==== 1/4 inch (6.3 mm) Tip-Ring-Sleeve ====
+{{:T8S to 2 L1 Pro 1/4}}
+==== XLR ====
+#Connect your audio sources (instruments or microphones) to the inputs on the ToneMatch mixer
+#Connect the T8S power supply from the Power port of the T8S to a power outlet
+#Connect an XLR cable from the Main Out R port of the mixer to the right-side L1 system
+#*Tip: If connecting to channels 1 or 2 on the second system, set the ToneMatch selector for that channel to OFF
+#Connect an XLR cable from the Main Out L port of the mixer to the left-side L1 system.
+#*Tip: If connecting to channels 1 or 2 on the second system, set the ToneMatch selector for that channel to OFF.
+<ref>[https://support.bose.com/s/display-articles?productId=01t8c00000OydHYAAZ&articleId=ka08c000001gBWrAAM&language=en_US Bose Support Article]</ref>
+=== {{T8S}} to Two Single {{L1P}} Mono Daisy Chain ===
+Connect the {{T8S}} to the first {{L1P}}
+[[File:T8S ToneMatch Port to L1 Pro32.jpg|400px]]
+Then connect the output of the first {{L1P}} to the second {{L1P}}
+{{:L1 Pro Daisy Chain}}
@@ Line 25: / Line 49: @@
 [[Category:T8S]]
 [[Category:L1 Pro]]
+[[Category:Connections]]