Template:Sub2 with Sub1: Difference between revisions

(9 intermediate revisions by the same user not shown)

Line 1:

You can use a Sub1 and Sub2 together. The connection will be L1 Pro32 to Sub2 to Sub1

* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)

* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)

* Connect the Sub2 Line Out to the Sub1 (optional: use a SubMatch cable to the Sub1)

* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs

* Polarity: Plus on both

You can stack them or place them side by side. In any arrangement where the grilles fit completely within a 30-inch (75 cm) diameter sphere, your two Subs will act like a single one, only louder. Note: Placing the Subs on either side of the L1 Pro32 power stand does not meet this criteria.

There are two options. Either is fine. Choose the one you prefer.

;Option 1: Same crossover frequency applied to both Sub1 and Sub2 (200—37Hz)

# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)

# Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR

#* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.

#* On the Sub2 set the Line Out EQ to Full (Full Range)

# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs

# Polarity: Plus on both

; Option 2: Crossover frequencies: <br>Sub2: 100—37 Hz <br>Sub1: 200—100 Hz

# Connect the L1 Pro32 Line Out to the Sub2 (with an XLR cable and power the Sub2 with the supplied IEC power cable).

# On the Sub2 set the LINE IN EQ to LPF [Low Pass Filter] (this sets the crossover to 100 Hz)

# On the Sub2 set the LINE OUT EQ to HPF [High Pass Filter] (this sets the Line Out to send 100 Hz and higher)

# Connect the Sub2 LINE OUT to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.

# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs

# Polarity: Plus on both

<!--

For more information start at 1:23 in the video below.<br>

<html>

-->

----

[[Category:Sub]]

[[Category:Connections]]

@@ Line 1: / Line 1: @@
 You can use a Sub1 and Sub2 together. The connection will be L1 Pro32 to Sub2 to Sub1
-* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)
-* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)
-* Connect the Sub2 Line Out to the Sub1 (optional: use a SubMatch cable to the Sub1)
-* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
-* Polarity: Plus on both
+You can stack them or place them side by side.  In any arrangement where the grilles fit completely within a 30-inch (75 cm) diameter sphere, your two Subs will act like a single one, only louder. Note: Placing the Subs on either side of the L1 Pro32 power stand does not meet this criteria.
+There are two options. Either is fine. Choose the one you prefer.
+;Option 1: Same crossover frequency applied to both Sub1 and Sub2 (200&mdash;37Hz)
+# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)
+# Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR
+#* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
+#* On the Sub2 set the Line Out EQ to Full (Full Range)
+# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
+# Polarity: Plus on both
+; Option 2: Crossover frequencies: <br>Sub2: 100&mdash;37 Hz <br>Sub1: 200&mdash;100 Hz
+# Connect the L1 Pro32 Line Out to the Sub2 (with an XLR cable and power the Sub2 with the supplied IEC power cable).
+# On the Sub2 set the LINE IN EQ to LPF [Low Pass Filter] (this sets the crossover to 100 Hz)
+# On the Sub2 set the LINE OUT EQ to HPF [High Pass Filter] (this sets the Line Out to send 100 Hz and higher)
+# Connect the Sub2 LINE OUT to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
+# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
+# Polarity: Plus on both
+<!--
 For more information start at 1:23 in the video below.<br>
 <html>
 <iframe width="560" height="315" src="https://www.youtube.com/embed/kQ4Pon0DLcs" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>
+-->
 ----
 [[Category:Sub]]
 [[Category:Connections]]