Template:ToneMatch Power Supply: Difference between revisions

(4 intermediate revisions by the same user not shown)

Line 1:

ToneMatch® Audio Engine power supply. This is the power supply for the {{ToneMatch Mixer}}. You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, or or non-Bose equipment. You will need a one of these if you have two {{ToneMatch Mixer}}s running into a single {{Model II nl}} or {{Model 1S nl}}. — details below the picture.

ToneMatch® Audio Engine power supply.

This is the power supply for the {{ToneMatch Mixer}}.

==== Not Required with {{L1P}} ====

The {{L1P}} systems have a ToneMatch port that can supply power to any ToneMatch mixer.

==== Required with Earlier Systems except {{Model II}} ====

You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, or non-Bose equipment. You will need a one of these if you have two {{ToneMatch Mixer}}s running into a single {{Model II nl}} or {{Model 1S nl}}. — details below the picture.

[[File:L1 tonematch powersupply acc bl lg.jpg|link=https://www.bose.com/en_us/products/speakers/speaker_accessories/l1_tonematch_powersupply_acc.html#v=l1_tonematch_powersupply_acc_black|100px|T1 ToneMatch® Audio Engine power supply]]

Line 14:

Line 24:

See: [[T1 ToneMatch® Audio Engine / Connections to Model II|Connecting Two T1®s to a Model II]] for details.

----

~~Close up of~~ the connector that ~~goes to~~ the ~~{{ToneMatch Mixer}}, just~~ in ~~case you damage~~ the ~~cable and have to replace the connector~~.

If you disassemble the Ethercon connector (not recommended), it's tricky to reassemble it.

[[File:NE8MX-B-1.jpg|400px]]

Note: There are small guides on the grey piece that slide into the slots in the barrel.

~~Note~~: ~~The picture is taken with the flat side facing the camera. The release clip is on the other side~~.

[[File:NE8MX-B-12.jpg|400px]]

~~[[Image:T1 Power Supply RJ 45 Connector.jpg|400px|Close up of the RJ45 connector]]~~

[[Media:BDA 564 - etherCON NE8MX-1 & NE8MX-B-1 - RJ45 cable connector carrier.pdf]]

~~[[File:NE8MX~~-B-1.~~jpg]]~~

----

Close up of the connector that goes to the {{ToneMatch Mixer}}, just in case you damage the cable and have to replace the connector.

Note: The picture is taken with the flat side facing the camera. The release clip is on the other side.

[[~~File~~:~~st-ne8mx-B-1~~.~~PDF~~|~~NE8MX-B-1 Assembly Instructions.pdf~~]]

[[Image:T1 Power Supply RJ 45 Connector.jpg|400px|Close up of the RJ45 connector]]

Line 32:

Line 50:

[[Category:T1]]

[[Category:T4S]]

[[Category:T8S]]

[[Category:Connections]]

[[Category:Bose Link]]

@@ Line 1: / Line 1: @@
-ToneMatch® Audio Engine power supply. This is the power supply for the {{ToneMatch Mixer}}. You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, or  or non-Bose equipment. You will need a one of these if you have two {{ToneMatch Mixer}}s running into a single {{Model II nl}} or {{Model 1S nl}}.  &mdash;  details below the picture.
+ToneMatch® Audio Engine power supply.
+This is the power supply for the {{ToneMatch Mixer}}.
+==== Not Required with {{L1P}} ====
+The {{L1P}} systems have a ToneMatch port that can supply power to any ToneMatch mixer.
+==== Required with Earlier Systems except {{Model II}} ====
+You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, or non-Bose equipment. You will need a one of these if you have two {{ToneMatch Mixer}}s running into a single {{Model II nl}} or {{Model 1S nl}}.  &mdash;  details below the picture.
 [[File:L1 tonematch powersupply acc bl lg.jpg|link=https://www.bose.com/en_us/products/speakers/speaker_accessories/l1_tonematch_powersupply_acc.html#v=l1_tonematch_powersupply_acc_black|100px|T1 ToneMatch® Audio Engine power supply]]
@@ Line 14: / Line 24: @@
 See: [[T1 ToneMatch® Audio Engine / Connections to Model II|Connecting Two T1®s to a Model II]] for details.
 ----
-Close up of the connector that goes to the {{ToneMatch Mixer}}, just in case you damage the cable and have to replace the connector.
+If you disassemble the Ethercon connector (not recommended), it's tricky to reassemble it.
+[[File:NE8MX-B-1.jpg|400px]]
+Note: There are small guides on the grey piece that slide into the slots in the barrel.
-Note:  The picture is taken with the flat side facing the camera. The release clip is on the other side.
+[[File:NE8MX-B-12.jpg|400px]]
-[[Image:T1 Power Supply RJ 45 Connector.jpg|400px|Close up of the RJ45 connector]]
+[[Media:BDA 564 - etherCON NE8MX-1 & NE8MX-B-1 - RJ45 cable connector carrier.pdf]]
-[[File:NE8MX-B-1.jpg]]
+----
+Close up of the connector that goes to the {{ToneMatch Mixer}}, just in case you damage the cable and have to replace the connector.
+Note:  The picture is taken with the flat side facing the camera. The release clip is on the other side.
-[[File:st-ne8mx-B-1.PDF|NE8MX-B-1 Assembly Instructions.pdf]]
+[[Image:T1 Power Supply RJ 45 Connector.jpg|400px|Close up of the RJ45 connector]]
@@ Line 32: / Line 50: @@
 [[Category:T1]]
+[[Category:T4S]]
+[[Category:T8S]]
+[[Category:Connections]]
 [[Category:Bose Link]]