Template:ToneMatch Mixers to F1 Model 812: Difference between revisions

(2 intermediate revisions by the same user not shown)

Line 1:

<!--

#Plug in your ToneMatch mixer and F1 812 to power and then connect the audio path using an XLR or TRS ¼-inch cable.

#Power on the devices.

#Set the F1 812 switch to Line Level and turn up the Volume knob to the 12 o’clock center detent.

#Set the ToneMatch mixer Master output to 10 o’clock.

#Set the ToneMatch mixer Master output to 10 o’clock. -->  <!--

#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs � Input Level on the ToneMatch mixer to monitor the input level.

#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs | Input Level on the ToneMatch mixer to monitor the input level.

#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs � Output Level on the ToneMatch mixer.

#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs | Output Level on the ToneMatch mixer.

-->

== Gain Staging ==

For each {{F1}}

=== {{F1}} Channel 1 Combo Input ===

The use an XLR or ¼ inch Tip-Ring-Sleeve jack cable.

=== MIC / LINE LEVEL ===

Set this to LINE LEVEL

==== Volume Control ====

Use the Input 1 volume control.

[[File:F1 812 Channel 1 only.png]]

# Set the Input 1 '''Volume''' control to the 0 (zero) position.

# Connect the {{T8S}} Main Output to the Input 1

# Adjust the volume of the {{T8S}} Main Output to the maximum output without distortion. This is probably between 10:00 o'clock and 12:00 o'clock on the Master Output

# While playing music through the {{T8S}}, increase the '''Volume''' level so that the '''Signal/Clip''' indicator glows green with flickers of red. This will probably be around 9:00-11:00 o'clock

# If the '''Signal/Clip''' indicator glows red, decrease the '''Volume''' level so that it glows only green or red. If you see red flashes longer than one second, turn down the volume.

----

@@ Line 1: / Line 1: @@
+<!--
 #Plug in your ToneMatch mixer and F1 812 to power and then connect the audio path using an XLR or TRS ¼-inch cable.
 #Power on the devices.
 #Set the F1 812 switch to Line Level and turn up the Volume knob to the 12 o’clock center detent.
-#Set the ToneMatch mixer Master output to 10 o’clock. <!-- This is the mixer’s unity output.-->
+#Set the ToneMatch mixer Master output to 10 o’clock. --> <!-- This is the mixer’s unity output.-->  <!--
-#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs � Input Level on the ToneMatch mixer to monitor the input level.
+#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs | Input Level on the ToneMatch mixer to monitor the input level.
-#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs � Output Level on the ToneMatch mixer.
+#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs | Output Level on the ToneMatch mixer.
+-->
+== Gain Staging ==
+For each {{F1}}
+=== {{F1}} Channel 1 Combo Input  ===
+The use an XLR or  ¼ inch Tip-Ring-Sleeve jack cable.
+=== MIC / LINE LEVEL ===
+Set this to LINE LEVEL
+==== Volume Control  ====
+Use the Input 1 volume control.
+[[File:F1 812 Channel 1 only.png]]
+# Set the Input 1 '''Volume''' control to the 0 (zero) position.
+# Connect the {{T8S}} Main Output to the Input 1
+# Adjust the volume of the {{T8S}} Main Output to the maximum output without distortion. This is probably between 10:00 o'clock and 12:00 o'clock on the Master Output
+# While playing music through the {{T8S}}, increase the '''Volume''' level so that the '''Signal/Clip''' indicator glows green with flickers of red. This will probably be around 9:00-11:00 o'clock
+# If the '''Signal/Clip''' indicator glows red, decrease the '''Volume''' level so that it glows only green or red. If you see red flashes longer than one second, turn down the volume.
 ----