Bose Portable PA Knowledge

T8S to L1 Model II: Difference between revisions

← Older edit
ST (talk | contribs)
Bureaucrats, Interface administrators, Administrators
20,075 edits
VisualWikitext
m used template:Balanced TRS from T8S to L1 Model II
mNo edit summary
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
<div class="tocdiv">
    <div>__TOC__</div>
    <div><h2>Introduction</h2>
Connect a {{T8S}} to two {{Model II}}s or two {{Model 1S}} or one of each.
;Recommendation:If you are panning everything up the middle like a traditional front of house setup, set up the L1 systems at least 20 feet (6 meters) apart. If you pan each sound source to only one L1 system, this recommendation does not apply. For more information see: [[Stereo / Mono / Distributed Systems]]
* Connect the ToneMatch Power Supply to the {{T8S}} for power.
* Always use the ToneMatch Power Supply connected to the {{T8S}} ToneMatch port.
* '''Do not use the ToneMatch port to connect to a L1 power stand'''. The {{T8S}} draws more power than the L1 power stand can supply.     
Related articles
* [[T8S to One L1 Model II]]
* [[T4S to Two Model II]]   
    </div>
</div> 
== Connect the T8S to {{Model II}} ==
== Connect the T8S to {{Model II}} ==
 
=== 1/4 inch (6.3 mm) Tip-Ring-Sleeve Outputs ===
[[File:T8S to L1 Model II.jpg|600px]]
[[File:T8S to L1 Model II.jpg|600px]]


{{Balanced TRS from T8S to L1 Model II}}
{{Balanced TRS from T8S to L1 Model II}}


Connect the ToneMatch Power Supply to the {{T8S}} for power.


Set the {{Model II}} Analog Input Trims to about 9:00 o'clock.
Set the {{Model II}} Analog Input Trims to about 9:00 o'clock.


<!--
=== XLR Outputs ===
{{#lst:L1® Model II|AnalogInput}}
-->


== Gain Staging ==
[[File:T8S XLR to L1 Model II.jpg|600px]]
For each {{Model II}}


=== {{Model II}} Analog Input  ===
{{Balanced XLR |Source= [[T8S]]|Target= {{Model II}}  
The Analog input is a ¼ inch balanced input jack.
}}


[[Image:Model 1S Analog Input Detail.png]]
== L1 Model II Gain Staging ==
 
For each {{Model II}}  
 
==== Analog input trim (volume, or gain) control  ====
There is a trim control for the analog input.
 
[[Image:Model II Analog Input Trim.png]]
 
# Set the '''Trim''' control on the power stand to the 0 (zero) position.
# Connect the {{T8S}} Main Output to the Analog Input
# Adjust the volume of the {{T8S}} Main Output to the maximum output without distortion. This is probably between 10:00 o'clock and 12:00 o'clock on the Master Output
# While playing the source, increase the '''Trim''' level so that the '''Signal/Clip''' indicator glows green or yellow. This will probably be around 9:00-11:00 o'clock
# If the '''Signal/Clip''' indicator glows red, decrease the '''Trim''' level so that it glows only green or yellow.


[[Image:Model II Analog Input Level Green.png|Model 1S Analog Input]]
{{L1 Model II Analog Input Gain Staging|Device={{T8S}}}}
----
----
[[Category:T8S]]
[[Category:T8S]]
[[Category:Model II]]
[[Category:Model II]]
[[Category:Connections]]
Retrieved from "https://boseperformer.com/T8S_to_L1_Model_II"