T1 ToneMatch® Audio Engine to F1 System: Difference between revisions
| (4 intermediate revisions by the same user not shown) | |||
| Line 15: | Line 15: | ||
=== {{T1 nl}} to F1 Model 812 (not F1 Subwoofer) === | === {{T1 nl}} to F1 Model 812 (not F1 Subwoofer) === | ||
{{F1 icon}}{{t1 icon}} | {{F1 icon}}{{t1 icon}} | ||
If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the {{t1}} to the F1 Model 812 instead of the F1 Subwoofer. | If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the {{t1}} to the F1 Model 812 instead of the F1 Subwoofer. Then connect the F1 Model 812 LINE OUT to the F1 Subwoofer. | ||
=== {{T1 nl}} with {{l1}} as stage monitor with F1 Model 812 as Front of House === | === {{T1 nl}} with {{l1}} as stage monitor with F1 Model 812 as Front of House === | ||
| Line 28: | Line 28: | ||
To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input. | To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input. Use a ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve cable. | ||
[[Image:TrsMtrsM.png|600px]] | |||
[[Image:T1 to F1 Model 812 Mono.png|600px]] | [[Image:T1 to F1 Model 812 Mono.png|600px]] | ||
| Line 37: | Line 38: | ||
'''For best results use a balanced connection | '''For best results use a balanced connection | ||
; ¼ Inch Tip-Ring-Sleeve | ; ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve''' | ||
A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection. | A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection. | ||
| Line 47: | Line 48: | ||
=== XLR connection from F1 Model 812 Line Out to second F1 Model 812 Channel 1 === | === XLR connection from F1 Model 812 Line Out to second F1 Model 812 Channel 1 === | ||
Use an ordinary microphone cable to connect the first F1 Model 812 to the second one. | Use an ordinary microphone cable to connect the first F1 Model 812 to the second one. | ||
=== General settings === | |||
* Turn the volume off for any channels you are not using. In the diagram above, you would turn off channel 2 for both F1 systems. | |||
* On the first F1, set the Level Control to MIC | |||
* On the second F1, set the Level Control to LINE | |||
* Set the volume on the second F1 to 10:00 o'clock. Then adjust the volume on the second F1 to match the output of the first F1 (if necessary). It's likely, you will have the volume on the second F1 lower than the first. That is normal. | |||
** Note: The volume control on the first F1 will raise and lower the volume on the second F1 | |||
=== Using an F1 Subwoofer === | === Using an F1 Subwoofer === | ||
| Line 53: | Line 62: | ||
[[Image:T1 to F1 Model 812 with F1 Subwoofer.png]] | [[Image:T1 to F1 Model 812 with F1 Subwoofer.png]] | ||
== Master / Monitor or | == Master / Monitor == | ||
=== No L1® Model II or Model 1S for Monitor === | |||
Consider running a {{Compact}} for your monitor. | |||
Your signal path would be T1® Master Output to Compact to F1 Model 812. Note: When you change the volume on the {{Compact}} it will affect the volume to the F1 Model 812 | |||
-=OR=- | |||
You can take a line from the end of the F1 signal chain to a {{Compact}} or third party monitor. This will allow you to change the volume on the {{Compact}} or monitor without affecting the volume on the F1 Model 812. | |||
[[File:T1 F1 Model 812 F1 Subwoofer Compact or Monitor.png]] | |||
=== T1® Aux to Monitor === | |||
You can use the T1 Aux output to run a separate signal to your monitor. | |||
See [[T1 ToneMatch® Audio Engine / Aux]] for details. | See [[T1 ToneMatch® Audio Engine / Aux]] for details. | ||
The {{Compact}} can be used for a monitor. | |||
[[File:T1 F1 Model 812 Compact or Monitor.png]] | [[File:T1 F1 Model 812 Compact or Monitor.png]] | ||