T1 ToneMatch® Audio Engine / Daisy Chain: Difference between revisions

(5 intermediate revisions by the same user not shown)

Line 3:

[[Image:T1x2IntoModelIIa.gif]]

In this example we have two {{T1}}s. (T1®s)

In this example, we have two {{T1}}s. (T1®s)

#{{t1r}} on the left connected to the {{Model II}} through the [[ToneMatch® Port]]

#{{t1r}}on the right connected to the {{t1r}} on the left through the Master Analog ¼ inch jack to the other T1® Channel 4

Use a balanced (Tip-Ring-Sleeve) cable if possible.

{{Balanced TRS

|Input= {{T1}} Master Output

|Output= {{T1}} Channel 4 or Channel 5

|discussion page = link to forum discussion (optional) e.g. discussion in the Bose Message Board

}}

If you use an unbalanced cable (Tip-Sleeve) between the first and second {{T1}}, you will have a lower signal to noise ratio than using a balanced cable (Tip-Ring-Sleeve). This means you will have more noise, and because you will have to turn up the volume on the second {{T1}} you will be amplifying the noise.

This allows the performer using {{t1r}} #1 to control the overall volume of both T1®s. If the performer controlling T1® # does not adjust the volume of Channel 4, Changing the Master Volume maintains the relative balance between T1® #1 and T1® #2

Line 22:

Line 36:

[[Image:T1 Daisy Chain to Compact.png]]

In this example we have two {{T1}}s. (T1®s)

In this example, we have two {{T1}}s. (T1®s)

#{{t1r}} on the left connected to ~~the {{Compact}} through the~~ [[~~ToneMatch® Port~~]]

#{{t1r}} on the left connected to [[L1%C2%AE_Compact#Channel_2|Compact Channel 2]]

#{{t1r}}on the right connected to the {{t1r}} on the left through the Master Analog ¼ inch jack to the other T1® Channel 4

@@ Line 3: / Line 3: @@
 [[Image:T1x2IntoModelIIa.gif]]
-In this example we have two {{T1}}s. (T1®s)
+In this example, we have two {{T1}}s. (T1®s)
 #{{t1r}} on the left connected to the {{Model II}} through the [[ToneMatch® Port]]
 #{{t1r}}on the right connected to the {{t1r}} on the left through the Master Analog ¼ inch jack to the other T1® Channel 4
+Use a balanced (Tip-Ring-Sleeve) cable if possible.
+{{Balanced TRS
+|Input= {{T1}} Master Output
+|Output= {{T1}} Channel 4 or Channel 5
+|discussion page = link to forum discussion (optional) e.g. discussion in the Bose Message Board
+}}
+If you use an unbalanced cable (Tip-Sleeve) between the first and second {{T1}}, you will have a lower signal to noise ratio than using a balanced cable (Tip-Ring-Sleeve). This means you will have more noise, and because you will have to turn up the volume on the second {{T1}} you will be amplifying the noise.
 This allows the performer using {{t1r}} #1 to control the overall volume of both T1®s. If the performer controlling T1® # does not adjust the volume of Channel 4, Changing the Master Volume maintains the relative balance between T1® #1 and T1® #2
@@ Line 22: / Line 36: @@
 [[Image:T1 Daisy Chain to Compact.png]]
-In this example we have two {{T1}}s. (T1®s)
+In this example, we have two {{T1}}s. (T1®s)
-#{{t1r}} on the left connected to the {{Compact}} through the [[ToneMatch® Port]]
+#{{t1r}} on the left connected to  [[L1%C2%AE_Compact#Channel_2|Compact Channel 2]]
 #{{t1r}}on the right connected to the {{t1r}} on the left through the Master Analog ¼ inch jack to the other T1® Channel 4