Denon DN-MC6000: Difference between revisions
mNo edit summary |
m →Mono |
||
| (13 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact. | <table><tr> | ||
<td valign="top" width="250">__TOC__</td> | |||
<td valign="top">Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact. | |||
</td> | |||
</tr></table> | |||
==== Mono ==== | |||
This mixer has a mono switch and when connecting to a single L1® you should use this switch set to MONO and connect to only one output. Do NOT use any kind of Y-cable to join the two mixer outputs. See [[Why Not Wye]] for details. | |||
See the diagram below (from [http://b06ba727c886717f9577-fff53f927840131da4fecbedd819996a.r74.cf2.rackcdn.com//1216/documents/DN-MC6000_ownersmanual.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)] | |||
[[Image:Denon DN-MC6000 Output.png]] | |||
Running mono, set the output to MONO above and connect one XLR output from the Denon DN-MC6000 to the [[L1%C2%AE_Model_II#Analog_Input|Model II Analog input]] or [[L1%C2%AE_Model_1S#Analog_Input|Model 1S Analog input]]. Set the input trim so that you have a solid green light on the Signal/Clip light. Yellow is okay. If you see red, turn down the trim. | |||
[[Image:Model II Analog Input Trim.png]] | |||
or [[L1®_Compact#Channel_2|Compact Channel 2]] | |||
[[Image:Compact Channel 2 Balanced.png]] | |||
With a cable like this: | |||
[[Image:XLR to TRS mp106.jpg]] | |||
[http://www.audiopile.net/products/Mic_Instr_Cables/MP_Adaptor_Cbls/MP-105/MP-105_cutsheet.shtml Source: Audiopile.net] | |||
Technical Description: | |||
The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment. | |||
The Female XLR end is wired through to the 1/4" Male TRS end as follows: | |||
* Pin One FXLR to Sleeve of MTRS | |||
* Pin Two FXLR to Tip of MTRS | |||
* Pin Three FXLR to Ring of MTRS | |||
The 1/4" MTRS end is an EWI model P292S-BKG | |||
The FXLR end is an EWI model ES3FB-GDP | |||
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors. | |||
===== Booth Out ===== | |||
It also appears from the documentation (page 26) that the Mono switch also affects the Booth Out. Note: Your work-flow may be different if you use the Booth out. | |||
If you want to use the Booth out, use a ¼ inch jack Tip-Ring-Sleeve to ¼ inch jack Tip-Ring-Sleeve cable (ideal), or ¼ inch jack Tip-Sleeve to ¼ inch jack Tip-Sleeve cable. | |||
==== Stereo ==== | |||
See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)] | See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)] | ||
[[Image:Denon DN-MC6000 Output.png]] | [[Image:Denon DN-MC6000 Output Stereo.png]] | ||
Running stereo with two L1®s, set the output to STEREO above and connect one cable from each output to a [[L1%C2%AE_Model_II#Analog_Input|Model II Analog input]] or [[L1%C2%AE_Model_1S#Analog_Input|Model 1S Analog input]] | |||
[[Image:Model II Analog Input Trim.png]] | |||
or [[L1®_Compact#Channel_2|Compact Channel 2]] | |||
[[Image:Compact Channel 2 Balanced.png]] | |||
With a cable like this: | With a cable like this: | ||
| Line 31: | Line 83: | ||
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors. | The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors. | ||
---- | |||
[[Category:Denon]] | |||
[[Category:Mixer]] | |||