T1 ToneMatch® Audio Engine / Aux: Difference between revisions

(6 intermediate revisions by the same user not shown)

Line 1:

=== Overview ===

[[Image:T1Aux.png|right]]

The output of any of the Channels 1, 2, 3, 4/5 can be sent to the Aux out. You can take the Aux out to provide a separate mix for recording or running to another {{L1}} or separate amplification system.

Line 13:

Line 15:

----

[[Image:T1AuxOutput.png]]

=== Setting the Tap Point ===

Line 30:

Line 34:

What To Do:

* Check if the Aux output is configured for the desired tap point for each input channel. Refer to “Routing input signals to the Aux output” on page 26.<ref name="AuxTap">~~Routing input signals to the Aux output on page 26 of {{T1 Manual}}~~</ref>

* Check if the Aux output is configured for the desired tap point for each input channel. Refer to “Routing input signals to the Aux output” on page 26.<ref name="AuxTap"></ref>

Note: No reverb comes from the Aux output even if the tap point is Pre or Post.

Line 36:

Line 40:

* Verify that each input assigns the desired signal level to the Aux output.

=== Aux to a separate System ===

=== Aux Out to a {{S1}} ===

The Aux Out is balanced mono and suitable to connect to the {{S1}} Channel 1 or 2.

For best results use a 1/4 inch (6 mm) Tip-Ring-Sleeve cable. A 1/4 inch (6 mm) Tip-Sleeve cable will have up to -6dB lower signal and be more susceptible to line noise.

=== Aux Out to a separate System ===

==== Aux Out to Headphones ====

The Aux Out is balanced mono intended to be connected to the balanced input of another device at line-level. This may also work with headphones but the volume will be very low and likely not loud enough to be heard over live stage volume.

If you connect to a stereo input, the signals for Left and Right may cancel out. This might not be an issue for headphones as the Left and Right signals are not combined.

==== Aux Out to In-Ear-Monitors ====

The Aux Out is balanced mono intended to be connected to the balanced input of another device at line-level. This may also work with headphones but the volume will be very low and likely not loud enough to be heard over live stage volume.

If you use an In-Ear-Monitor system that has built-in amplification, this may work.

If you connect to a stereo input, the signals for Left and Right may cancel out. This might not be an issue for headphones as the Left and Right signals are not combined.

==== Input Directed to Aux Out Only ====

To direct an input exclusively to Aux see: [[T1 ToneMatch® Audio Engine / Aux to a Separate System]]

@@ Line 1: / Line 1: @@
+=== Overview ===
 [[Image:T1Aux.png|right]]
 The output of any of the Channels 1, 2, 3, 4/5 can be sent to the Aux out. You can take the Aux out to provide a separate mix for recording or running to another {{L1}} or separate amplification system.
@@ Line 13: / Line 15: @@
 ----
+[[Image:T1AuxOutput.png]]
+=== Setting the Tap Point ===
 {{:T1® Aux / Dry or Pre or Post}}
@@ Line 30: / Line 34: @@
 What To Do:
-* Check if the Aux output is configured for the desired tap point for each input channel. Refer to “Routing input signals to the Aux output” on page 26.<ref name="AuxTap">Routing input signals to the Aux output on page 26 of {{T1 Manual}}</ref>
+* Check if the Aux output is configured for the desired tap point for each input channel. Refer to “Routing input signals to the Aux output” on page 26.<ref name="AuxTap"></ref>
 Note: No reverb comes from the Aux output even if the tap point is Pre or Post.
@@ Line 36: / Line 40: @@
 * Verify that each input assigns the desired signal level to the Aux output.
-=== Aux to a separate System ===
+=== Aux Out to a {{S1}} ===
+The Aux Out is balanced mono and suitable to connect to the {{S1}} Channel 1 or 2.
+For best results use a 1/4 inch (6 mm) Tip-Ring-Sleeve cable. A 1/4 inch (6 mm) Tip-Sleeve cable will have up to -6dB lower signal and be more susceptible to line noise.
+{{:S1 Pro with T1}}
+=== Aux Out to a separate System ===
+==== Aux Out to Headphones ====
+The Aux Out is balanced mono intended to be connected to the balanced input of another device at line-level. This may also work with headphones but the volume will be very low and likely not loud enough to be heard over live stage volume.
+If you connect to a stereo input, the signals for Left and Right may cancel out. This might not be an issue for headphones as the Left and Right signals are not combined.
+==== Aux Out to In-Ear-Monitors ====
+The Aux Out is balanced mono intended to be connected to the balanced input of another device at line-level. This may also work with headphones but the volume will be very low and likely not loud enough to be heard over live stage volume.
+If you use an In-Ear-Monitor system that has built-in amplification, this may work.
+If you connect to a stereo input, the signals for Left and Right may cancel out. This might not be an issue for headphones as the Left and Right signals are not combined.
+==== Input Directed to Aux Out Only ====
 To direct an input exclusively to Aux see: [[T1 ToneMatch® Audio Engine / Aux to a Separate System]]