Template:Sub2 with Sub1: Difference between revisions

(5 intermediate revisions by the same user not shown)

Line 1:

You can use a Sub1 and Sub2 together. The connection will be L1 Pro32 to Sub2 to Sub1

* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)

* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)

You can stack them or place them side by side. In any arrangement where the grilles fit completely within a 30-inch (75 cm) diameter sphere, your two Subs will act like a single one, only louder. Note: Placing the Subs on either side of the L1 Pro32 power stand does not meet this criteria.

* Connect the Sub2 ~~Line Out~~ to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.

* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs

There are two options. Either is fine. Choose the one you prefer.

* Polarity: Plus on both

;Option 1: Same crossover frequency applied to both Sub1 and Sub2 (200—37Hz)

# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)

# Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR

#* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.

#* On the Sub2 set the Line Out EQ to Full (Full Range)

# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs

# Polarity: Plus on both

; Option 2: Crossover frequencies: <br>Sub2: 100—37 Hz <br>Sub1: 200—100 Hz

# Connect the L1 Pro32 Line Out to the Sub2 (with an XLR cable and power the Sub2 with the supplied IEC power cable).

# On the Sub2 set the LINE IN EQ to LPF [Low Pass Filter] (this sets the crossover to 100 Hz)

# On the Sub2 set the LINE OUT EQ to HPF [High Pass Filter] (this sets the Line Out to send 100 Hz and higher)

# Connect the Sub2 LINE OUT to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.

# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs

# Polarity: Plus on both

<!--

For more information start at 1:23 in the video below.<br>

@@ Line 1: / Line 1: @@
 You can use a Sub1 and Sub2 together. The connection will be L1 Pro32 to Sub2 to Sub1
-* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)
-* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)
+You can stack them or place them side by side.  In any arrangement where the grilles fit completely within a 30-inch (75 cm) diameter sphere, your two Subs will act like a single one, only louder. Note: Placing the Subs on either side of the L1 Pro32 power stand does not meet this criteria.
-* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
-* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
+There are two options. Either is fine. Choose the one you prefer.
-* Polarity: Plus on both
+;Option 1: Same crossover frequency applied to both Sub1 and Sub2 (200&mdash;37Hz)
+# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)
+# Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR
+#* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
+#* On the Sub2 set the Line Out EQ to Full (Full Range)
+# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
+# Polarity: Plus on both
+; Option 2: Crossover frequencies: <br>Sub2: 100&mdash;37 Hz <br>Sub1: 200&mdash;100 Hz
+# Connect the L1 Pro32 Line Out to the Sub2 (with an XLR cable and power the Sub2 with the supplied IEC power cable).
+# On the Sub2 set the LINE IN EQ to LPF [Low Pass Filter] (this sets the crossover to 100 Hz)
+# On the Sub2 set the LINE OUT EQ to HPF [High Pass Filter] (this sets the Line Out to send 100 Hz and higher)
+# Connect the Sub2 LINE OUT to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
+# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
+# Polarity: Plus on both
 <!--
 For more information start at 1:23 in the video below.<br>