Template:L1 Compact with Sub1 or Sub2: Difference between revisions

(8 intermediate revisions by the same user not shown)

Line 3:

For best results, the signal flow should go from

<table>

<th>First L1 Compact</th><th>Second L1 Compact (if you have two)</th></tr>

# [[File:Sub1 Sub2 io panel to L1 Compact.jpg|thumb|Sub io panel]]The signal source (e.g., {{ToneMatch Mixer}}, mixer, DJ console) output to

# The Sub1 or Sub2 subwoofer LINE IN 1

# The Sub1 or Sub2 subwoofer LINE OUT 1 to

# [[File:Compact_Channel_2_Line_Level.png|thumb|Compact Channel 2]]The {{Compact}}

#* Connect to L1 Compact Channel 2

#* Set the ToneMatch switch to Line Level (down position)

#* Channel volume set to 12 o'clock.

</td>

<td>

# The signal source (e.g., {{ToneMatch Mixer}}, mixer, DJ console) output to

# The Sub1 or Sub2 subwoofer ~~Line Out~~ to

# The Sub1 or Sub2 subwoofer LINE IN 2

# The {{Compact}}

# The Sub1 or Sub2 subwoofer LINE OUT 2 to

#* Connect to Channel 2

# The second {{Compact}}

#* Connect to second L1 Compact Channel 2

#* Set the ToneMatch switch to Line Level (down position)

#* Channel volume set to 12 o'clock.

#* Channel volume set to 12 o'clock.

</td>

</tr>

</table>

;Note these settings on the Sub1 or Sub2

:👉 Set LINE IN EQ to '''L1'''

:👉 Set LINE OUT EQ to '''S1''' (Press and hold LINE OUT EQ button for 4 seconds)

Set up this way,

# The Sub1 or Sub2 handles frequencies from 40 Hz (Sub1) 37 Hz (Sub2) to 150 Hz

# The {{~~S1 Pro~~}} handles frequencies above 150 Hz

# The {{Compact}} handles frequencies above 150 Hz

<!--

The picture shows a stereo setup, but illustrates the principles for mono. The signal flow is from left to right.

Line 21:

Line 40:

[[File:S1 Pro with Sub HPF.jpg|560px]]

;Required cable

Use an XLR to {{1/4 TRS}} cable for best results.

[[File:XLRFemale to 14trs.jpg|300px]]

;Do not use an XLR cable from the Sub to {{Compact}} Channel 1

* {{Compact}} Channel 1 is for dynamic microphones and has a ToneMatch Preset for Handheld Vocal microphones permanently applied

* If you use an XLR to XLR cable, the signal will be too hot for the {{Compact}}

; Not recommended - Sound source to {{Compact}} and {{Compact}} Line Out to Sub

If you use the {{Compact}} as the sound source (e.g., microphone and guitar) and connect the {{Compact}} Line Out to the Sub

# The {{Compact}} will sound the same as without the subwoofer (~~down to~~ 65 Hz)

# The {{Compact}} will sound the same as without the subwoofer (65 Hz to 14 KHz)

# The Sub1 or Sub2 will cover from 40 Hz (Sub1) 37 Hz (Sub2) to 150 Hz

@@ Line 3: / Line 3: @@
 For best results, the signal flow should go from
+<table>
+<th>First L1 Compact</th><th>Second L1 Compact (if you have two)</th></tr>
+<tr><td>
+# [[File:Sub1 Sub2 io panel to L1 Compact.jpg|thumb|Sub io panel]]The signal source (e.g., {{ToneMatch Mixer}}, mixer, DJ console) output to
+# The Sub1 or Sub2 subwoofer LINE IN 1
+# The Sub1 or Sub2 subwoofer LINE OUT 1 to
+# [[File:Compact_Channel_2_Line_Level.png|thumb|Compact Channel 2]]The {{Compact}}
+#* Connect to L1 Compact Channel 2
+#* Set the ToneMatch switch to Line Level (down position)
+#* Channel volume set to 12&nbsp;o'clock.
+</td>
+<td>
 # The signal source (e.g., {{ToneMatch Mixer}}, mixer, DJ console) output to
-# The Sub1 or Sub2 subwoofer Line Out to
+# The Sub1 or Sub2 subwoofer LINE IN 2
-# The {{Compact}}
+# The Sub1 or Sub2 subwoofer LINE OUT 2 to
-#* Connect to Channel 2
+# The second {{Compact}}
+#* Connect to second L1 Compact Channel 2
 #* Set the ToneMatch switch to Line Level (down position)
-#* Channel volume set to 12 o'clock.
+#* Channel volume set to 12&nbsp;o'clock.
+</td>
+</tr>
+</table>
+;Note these settings on the Sub1 or Sub2
+:👉 Set LINE IN EQ to '''L1'''
+:👉 Set LINE OUT EQ to '''S1''' (Press and hold LINE OUT EQ button for 4 seconds)
 Set up this way,
 # The Sub1 or Sub2 handles frequencies from 40 Hz (Sub1) 37 Hz (Sub2) to 150 Hz
-# The {{S1 Pro}} handles frequencies above 150 Hz
+# The {{Compact}} handles frequencies above 150 Hz
 <!--
 The picture shows a stereo setup, but illustrates the principles for mono.  The signal flow is from left to right.
@@ Line 21: / Line 40: @@
 [[File:S1 Pro with Sub HPF.jpg|560px]]
+;Required cable
+Use an XLR to {{1/4 TRS}} cable for best results.
+[[File:XLRFemale to 14trs.jpg|300px]]
+;Do not use an XLR cable from the Sub to {{Compact}} Channel 1
+* {{Compact}} Channel 1 is for dynamic microphones and has a ToneMatch Preset for Handheld Vocal microphones permanently applied
+* If you use an XLR to XLR cable, the signal will be too hot for the {{Compact}}
+; Not recommended - Sound source to {{Compact}} and {{Compact}} Line Out to Sub
 If you use the {{Compact}} as the sound source (e.g., microphone and guitar) and connect the {{Compact}} Line Out to the Sub
-# The {{Compact}} will sound the same as without the subwoofer (down to 65 Hz)
+# The {{Compact}} will sound the same as without the subwoofer (65 Hz to 14 KHz)
 # The Sub1 or Sub2 will cover from 40 Hz (Sub1) 37 Hz (Sub2) to 150 Hz