Parametric EQ / Solving Problems: Difference between revisions

(25 intermediate revisions by 2 users not shown)

Line 1:

~~Troubleshooting with the~~ {{T1}} Parametric EQ

{{DivToc

|RightHead = Introduction

|RightBody = You can use the Parametric EQ feature to notch out a problem frequency. Here are a few real-world examples. <br>This article applies to all ToneMatch mixers (T1/T4S/T8S).

|Categories =

[[Category:Para EQ]]

[[Category:T1]]

[[Category:T4S]]

[[Category:T8S]]

}}

~~== Using Para EQ to solve a problem frequency ==~~

~~In this example a Bassist was having a problem with a resonant note (B flat).~~

=== Bassist With Excessive Resonance at B flat ===

Chuck-at-Bose provided this approach.<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/6531054674?r=1661015674#1661015674 Chuck-at-Bose talks about using the Para EQ to solve a problem frequency]</ref>

Line 16:

Line 25:

<tr>

# Adjust the '''Width''' control to as narrow a value as possible, so that only the problem is being affected, leaving the non-offending frequencies around it unchanged. The T1 goes down to ''one fifth'' (0.20) of an octave, which is great for 'notching out' problem notes. <br />

4. Adjust the '''Width''' control to as narrow a value as possible, so that only the problem is being affected, leaving the non-offending frequencies around it unchanged. The T1 goes down to ''one fifth'' (0.20) of an octave, which is great for 'notching out' problem notes. <br />

# Now adjust the '''Level'' control to cut (turn down) enough to make the problem go away, but not so much that the tone of the source is altered in an undesirable way. Values of -1 to -6 dB will often do the trick, though sometimes a more aggressive cut is necessary. Use your ears to find an appropriate balance between fixing the problem and adversely altering the tone of the source.

5. Now adjust the '''Level'' control to cut (turn down) enough to make the problem go away, but not so much that the tone of the source is altered in an undesirable way. Values of -1 to -6 dB will often do the trick, though sometimes a more aggressive cut is necessary. Use your ears to find an appropriate balance between fixing the problem and adversely altering the tone of the source.

</td>

<td>

Line 25:

Line 34:

</table>

=== Another Approach ===

=== Another Approach to Eliminating a Boomy Note ===

Hilmar-at-Bose had a different approach<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/6531054674?r=7421005674#7421005674 Hilmar-at-Bose talks about solving a boomy note]</ref>

~~Here is one method~~ to ~~eliminate~~ a ~~boomy note~~

a) set the level of the para EQ to a cut, say -10 dB

~~a) set the level of the para EQ to a cut, say -10 dB~~

b) set the width to fairly narrow, say .25 octaves

c) start with a rough estimate of the offending frequency and then move the frequency around until the offending note gets tamed best

d) you can press on the level control to toggle between on and off which gives you a direct A/B so you can judge the effect better

Line 42:

Line 52:

* 2nd octave on the guitar is from 160 Hz to 320 Hz (E3 to E4), A3 is at 220 Hz

Here is a cheat sheet http://www.phy.mtu.edu/~suits/notefreqs.html

Here is a cheat sheet: [http://www.phy.mtu.edu/~suits/notefreqs.html Frequency vs. Musical Notes Graphic from MIT]

=== Controlling Vocal Microphone Feedback ===

</noinclude>

=== Piezo Pickup Thump ===

If you have an Acoustic Guitar that is picking up low end thump from a percussive right hand technique use the Para EQ with settings like this.

*Level -15

*Frequency 50 Hz

*Width 0.50

[[Image:T1ParaEQNoThump.png]]

[http://bose.infopop.cc/eve/forums?a=tpc&f=7521050644&m=6771047194&r=4591097194 T1 and x bridge] - Strat man

<br>

=== Single Coil Buzz ===

Use the Noise Gate

[[Image:T1NoiseGate01.png]]

<br> [[Image:T1NoiseGateDefault.png]]

The default settings seem to work okay for me.

[http://bose.infopop.cc/eve/forums?a=tpc&s=8206048934&f=7521050644&m=3771027294&r=1191035105#1191035105 eliminating single coil buzz] - jayare and ST

<br>

=== Wind Noise ===

:A microphone responds to the movement of air and it does not care what caused the air to move. This means that a mic cannot distinguish between air movement originating from a talker, and air movement originating from local weather. Wind noise is a persistent problem with microphones but there are multiple ways to minimize unwanted noise.

~~Hope that helps~~

:Wind noise has a large amount of low frequency (bass) content, often described as “rumble.” Cutting out the extreme bass from a microphone signal is an effective method to reduce audible wind noise.

~~Hilmar~~

---- Source: [http://blog.shure.com/shure-notes/shure-tech-tip-methods-to-minimize-wind-noise/ shure tech tips to minimize wind noise]

Use the ParaEQ (Woody B called it the notch filter)

:I had an extremely windy gig last night. Even with windscreens on the mics they still had the wind rumble. I used the notch filter on my T1 to notch the wind sound out. I don't believe it's called a notch filter on the T1, but I don't remember the correct name. I just turned the volume way up, and adjusted the frequency until the wind noise was gone. I tried using the noise gate, but if it was high enough to eliminate the wind it also eliminated most of the vocals. Usually wind screens solve any wind problems I have, but the wind was so strong I kept my guitar case on stage to sit my guitar in, instead of using a stand. I believe the wind would have blown it over.

[http://bose.infopop.cc/eve/forums/a/tpc/f/1266055944/m/6571097974?r=5021027294#5021027294 What to do in windy conditions] - Woody B

<br>

----

----

[[Category:Para EQ]]

[[Category:T1]]

[[Category:T4S]]

[[Category:T8S]]

@@ Line 1: / Line 1: @@
-Troubleshooting with the {{T1}} Parametric EQ
+{{T4S icon}}{{T8S icon}}{{T1 icon}}
+{{DivToc
+|RightHead = Introduction
+|RightBody = You can use the Parametric EQ feature to notch out a problem frequency. Here are a few real-world examples. <br>This article applies to all ToneMatch mixers (T1/T4S/T8S).
+|Categories =
+[[Category:Para EQ]]
+[[Category:T1]]
+[[Category:T4S]]
+[[Category:T8S]]
+}}
-== Using Para EQ to solve a problem frequency ==
-In this example a Bassist was having a problem with a resonant note (B flat).
+=== Bassist With Excessive Resonance at B flat ===
 Chuck-at-Bose provided this approach.<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/6531054674?r=1661015674#1661015674 Chuck-at-Bose talks about using the Para EQ to solve a problem frequency]</ref>
 <table><tr><td valign="top">
@@ Line 16: / Line 25: @@
 <tr>
 <td valign="top">
-# Adjust the '''Width''' control to as narrow a value as possible, so that only the problem is being affected, leaving the non-offending frequencies around it unchanged. The T1 goes down to ''one fifth'' (0.20) of an octave, which is great for 'notching out' problem notes. <br />
+. Adjust the '''Width''' control to as narrow a value as possible, so that only the problem is being affected, leaving the non-offending frequencies around it unchanged. The T1 goes down to ''one fifth'' (0.20) of an octave, which is great for 'notching out' problem notes. <br />
-# Now adjust the '''Level'' control to cut (turn down) enough to make the problem go away, but not so much that the tone of the source is altered in an undesirable way. Values of    -1 to -6 dB will often do the trick, though sometimes a more aggressive cut is necessary. Use your ears to find an appropriate balance between fixing the problem and adversely altering the tone of the source.
+. Now adjust the '''Level'' control to cut (turn down) enough to make the problem go away, but not so much that the tone of the source is altered in an undesirable way. Values of    -1 to -6 dB will often do the trick, though sometimes a more aggressive cut is necessary. Use your ears to find an appropriate balance between fixing the problem and adversely altering the tone of the source.
 </td>
 <td>
@@ Line 25: / Line 34: @@
 </table>
-=== Another Approach ===
+=== Another Approach to Eliminating a Boomy Note ===
 Hilmar-at-Bose had a different approach<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/6531054674?r=7421005674#7421005674  Hilmar-at-Bose talks about solving a boomy note]</ref>
-Here is one method to eliminate a boomy note
+a) set the level of the para EQ to a cut, say -10 dB
-a) set the level of the para EQ to a cut, say -10 dB
 b) set the width to fairly narrow, say .25 octaves
 c) start with a rough estimate of the offending frequency and then move the frequency around until the offending note gets tamed best
 d) you can press on the level control to toggle between on and off which gives you a direct A/B so you can judge the effect better
@@ Line 42: / Line 52: @@
 * 2nd octave on the guitar is from 160 Hz to 320 Hz (E3 to E4), A3 is at 220 Hz
-Here is a cheat sheet http://www.phy.mtu.edu/~suits/notefreqs.html
+Here is a cheat sheet: [http://www.phy.mtu.edu/~suits/notefreqs.html Frequency vs. Musical Notes Graphic from MIT]
+<noinclude>
+=== Controlling Vocal Microphone Feedback ===
+{{:Feedback / T1 ToneMatch® Audio Engine}}
+</noinclude>
+=== Piezo Pickup Thump  ===
+If you have an Acoustic Guitar that is picking up low end thump from a percussive right hand technique use the Para EQ with settings like this.
+*Level -15
+*Frequency 50 Hz
+*Width 0.50
+[[Image:T1ParaEQNoThump.png]]
+[http://bose.infopop.cc/eve/forums?a=tpc&f=7521050644&m=6771047194&r=4591097194 T1 and x bridge] - Strat man
+<br>
+=== Single Coil Buzz  ===
+Use the Noise Gate
+[[Image:T1NoiseGate01.png]]
+<br> [[Image:T1NoiseGateDefault.png]]
+The default settings seem to work okay for me.
+[http://bose.infopop.cc/eve/forums?a=tpc&s=8206048934&f=7521050644&m=3771027294&r=1191035105#1191035105 eliminating single coil buzz] - jayare and ST
+<br>
+<br>
+=== Wind Noise  ===
+:A microphone responds to the movement of air and it does not care what caused the air to move.  This means that a mic cannot distinguish between air movement originating from a talker, and air movement originating from local weather.  Wind noise is a persistent problem with microphones but there are multiple ways to minimize unwanted noise.
-Hope that helps
+:Wind noise has a large amount of low frequency (bass) content, often described as “rumble.”  Cutting out the extreme bass from a microphone signal is an effective method to reduce audible wind noise.
-Hilmar
+---- Source: [http://blog.shure.com/shure-notes/shure-tech-tip-methods-to-minimize-wind-noise/ shure tech tips to minimize wind noise]
+Use the ParaEQ (Woody B called it the notch filter)
+:I had an extremely windy gig last night. Even with windscreens on the mics they still had the wind rumble. I used the notch filter on my T1 to notch the wind sound out. I don't believe it's called a notch filter on the T1, but I don't remember the correct name. I just turned the volume way up, and adjusted the frequency until the wind noise was gone. I tried using the noise gate, but if it was high enough to eliminate the wind it also eliminated most of the vocals. Usually wind screens solve any wind problems I have, but the wind was so strong I kept my guitar case on stage to sit my guitar in, instead of using a stand. I believe the wind would have blown it over.
+[http://bose.infopop.cc/eve/forums/a/tpc/f/1266055944/m/6571097974?r=5021027294#5021027294 What to do in windy conditions] - Woody B
+<br>
 ----
 <references />
+----
+[[Category:Para EQ]]
 [[Category:T1]]
+[[Category:T4S]]
+[[Category:T8S]]