Rubber Feet for L1®: Difference between revisions
m New page: <html> I removed a nearly new foot from a Model II. The measurements are as follows:<br>Diameter 1-3/16" X height 3/8" (30mm X 9.6mm)<br><br> The maximum height of 3/8" (9.6mm) for the fe... |
m ST moved page Rubber Feet for L1® to Rubber Feet for L1® |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
<noinclude> | |||
{{Model II icon}}{{Model 1S icon}} | |||
</noinclude> | |||
[[Image:Rubber Feet for L1.png|200px|right|Rubber feet for L1®]] | |||
Mark (Le5) on the {{forum}} provided this helpful research about replacement rubber feet for the {{L1}}s. | |||
<html> | <html> | ||
I removed a nearly new foot from a Model II. The measurements are as follows:<br>Diameter 1-3/16" X height 3/8" (30mm X 9.6mm) | <div style="max-width:800px"> | ||
I removed a nearly new foot from a Model II. The measurements are as follows:<br>Diameter 1-3/16" X height 3/8" (30mm X 9.6mm)<br> | |||
The maximum height of 3/8" (9.6mm) for the feet is important for stability; <i>it is not recommended to use thicker feet because the ends of the fold out legs would be raised off of the floor</i><br><br> | The maximum height of 3/8" (9.6mm) for the feet is important for stability; <i>it is not recommended to use thicker feet because the ends of the fold out legs would be raised off of the floor</i><br><br> | ||
The recesses where the feet are installed will not accept a larger diameter than the original feet but 1" (25.4mm) should work fine. | The recesses where the feet are installed will not accept a larger diameter than the original feet but 1" (25.4mm) should work fine.<br> | ||
I did a bit of research for you for some possible replacement feet:< | I did a bit of research for you for some possible replacement feet:<ul> | ||
<a href="http://www.penn-elcom.com/default.asp?PN=F1690%20-%20F1697&LG=ENG" target="_blank">Penn Elcom F1690</a>< | <li> | ||
<a href="http://www.penn-elcom.com/default.asp?PN=F1690%20-%20F1697&LG=ENG" target="_blank">Penn Elcom F1690</a> | |||
</li> | |||
<li> | |||
<a href="https://www.digikey.ca/product-detail/en/keystone-electronics/723/36-723-ND/61962" target="_blank">Keystone Electronics 723 DigiKey</a> < | <a href="https://www.digikey.ca/product-detail/en/keystone-electronics/723/36-723-ND/61962" target="_blank">Keystone Electronics 723 DigiKey</a> </li> | ||
<li> | |||
<a href="http://www.mojotone.com/Cabinets_x/Feet_x/Mojotone-Rubber-Feet-1Wx3-8H-25-4x9-5mm" target="_blank">MojoTone Rubber Feet, 25.4X9.5mm</a>< | <a href="http://www.mojotone.com/Cabinets_x/Feet_x/Mojotone-Rubber-Feet-1Wx3-8H-25-4x9-5mm" target="_blank">MojoTone Rubber Feet, 25.4X9.5mm</a></li> | ||
</ul> | |||
This type of feet are commonly used under guitar amp cabinets, it's a matter of finding some of the correct height and of a diameter that will fit. These need to have a steel washer for the mounting screw.<br> | This type of feet are commonly used under guitar amp cabinets, it's a matter of finding some of the correct height and of a diameter that will fit. These need to have a steel washer for the mounting screw.<br> | ||
This should help you find suitable replacement feet. | |||
<br> | |||
Mark | |||
</div> | |||
</html> | </html> | ||