T1 ToneMatch® Audio Engine / Routing for Effects: Difference between revisions

(4 intermediate revisions by the same user not shown)

Line 1:

This article addresses some interesting options you have for routing your signal through the T1® to process effects more than once.

For ideas on how you can work with an external effects unit see: [[T1 ToneMatch® Audio Engine / Insert for External Effects]]

</td>

</tr></table>

There are several less than obvious things you can do with effects through the {{T1}}.

=== Parallel Effects ===

== Parallel Effects~~ ~~ ==

If you want to swap between two sets of effects or run two sets of effects at the same time (for example: two delays, two modulation effects, two reverbs)  try this.

Line 12:

Line 21:

*Now use the FX Mute buttons for Channels 1 and 2 to set which banks of effects will be used

**Channel 1 only

**Channel 2 only

**Channel 1 and Channel 2 in parallel

== Serial Effects~~ ~~ ==

=== Serial Effects ===

If you want to run some effects and then add more effects in series then take the output of one or more {{T1}} Channels to the Aux Output, then take the Aux Output and use that as the input to another T1® Channel

If you ~~want to run some effects and then add more effects in series then take the output of one or more {{T1}} Channels to the Aux Output, then take the Aux Output and use that~~ as the input to ~~another T1® Channel~~

Assume that you are using Channel 1 as the input where you want to do this:

~~Assume that you are using Channel 1 as the input where you want to do this: ~~

*Set the effects that you want on Channel 1

*Set the '''Aux''' tap to '''Pre'''

*Take a ¼ inch jack cable from the Aux Out to Channel 2 input

*Apply effects that you want applied to the output of Channel 1

*Now use the FX Mute buttons for Channels 1 and 2 to set which banks of effects will be used

**Channel 1 only

**Channel 2 only

**Channel 1 and Channel 2 in series

=== Foot Switch to Mute Effects ===

From Andy-at-Bose UK

<blockquote>First up hook up your vocal mic to, say, Channel 1 on the T1®. Next take a jack lead and connect it to the PRE AMP out on Channel 1. Take this lead and run it through either a keyboard style volume pedal or a make or break style footswitch. Run the signal from the pedal/footswitch into another T1® channel and set this channel up with the chosen vocal effects but make them 100% effect. Adjust the effected channel volume to get the desired blend of dry vocal to effected vocal. The pedal/footswitch will determine how much or if any signal will go to channel 2 and therefore whether or not an effect is added. </blockquote>

[http://bose.infopop.cc/eve/forums/a/tpc/f/8221072574/m/5991023595?r=9991094595#9991094595 Original Post]

This article is a stub. Please help us if you can by expanding it.

----

[[Category:T1]]

[[Category:Effects]]

</noinclude>

@@ Line 1: / Line 1: @@
+<table><tr>
+<td valign="top" width="250">__TOC__</td>
+<td valign="top">
+This article addresses some interesting options you have for routing your signal through the T1® to process effects more than once.
+For ideas on how you can work with an external effects unit see: [[T1 ToneMatch® Audio Engine / Insert for External Effects]]
+</td>
+</tr></table>
 There are several less than obvious things you can do with effects through the {{T1}}.
+=== Parallel Effects  ===
-== Parallel Effects<br>  ==
 If you want to swap between two sets of effects or run two sets of effects at the same time (for example: two delays, two modulation effects, two reverbs)&nbsp; try this.
@@ Line 12: / Line 21: @@
 *Now use the FX Mute buttons for Channels 1 and 2 to set which banks of effects will be used
 **Channel 1 only
 **Channel 2 only<br>
 **Channel 1 and Channel 2 in parallel<br>
-== Serial Effects<br> ==
+=== Serial Effects  ===
+If you want to run some effects and then add more effects in series then take the output of one or more {{T1}} Channels to the Aux Output, then take the Aux Output and use that as the input to another T1® Channel
-If you want to run some effects and then add more effects in series then take the output of one or more {{T1}} Channels to the Aux Output, then take the Aux Output and use that as the input to another T1® Channel<br>
+Assume that you are using Channel 1 as the input where you want to do this:<br>
-Assume that you are using Channel 1 as the input where you want to do this:<br>
+*Set the effects that you want on Channel 1
-*Set the effects that you want on Channel 1
+*Set the '''Aux''' tap to '''Pre'''
-*Set the '''Aux''' tap to '''Pre'''
 *Take a ¼ inch jack cable from the Aux Out to Channel 2 input
 *Apply effects that you want applied to the output of Channel 1
 *Now use the FX Mute buttons for Channels 1 and 2 to set which banks of effects will be used
 **Channel 1 only
 **Channel 2 only<br>
 **Channel 1 and Channel 2 in series<br>
+=== Foot Switch to Mute Effects<br>  ===
+From Andy-at-Bose UK<br>
+<blockquote>First up hook up your vocal mic to, say, Channel 1 on the T1®. Next take a jack lead and connect it to the PRE AMP out on Channel 1. Take this lead and run it through either a keyboard style volume pedal or a make or break style footswitch. Run the signal from the pedal/footswitch into another T1® channel and set this channel up with the chosen vocal effects but make them 100% effect. Adjust the effected channel volume to get the desired blend of dry vocal to effected vocal. The pedal/footswitch will determine how much or if any signal will go to channel 2 and therefore whether or not an effect is added.<br> </blockquote>
+[http://bose.infopop.cc/eve/forums/a/tpc/f/8221072574/m/5991023595?r=9991094595#9991094595 Original Post]<br>
+<br>
+<noinclude>
 <br>
 This article is a stub. Please help us if you can by expanding it.
+----
+[[Category:T1]]
+[[Category:Effects]]
+</noinclude>