PS1 Powerstand / Daisy Chain: Difference between revisions

(13 intermediate revisions by the same user not shown)

Line 1:

<table><tr><td>__TOC__</td><td>On the relatively rare occasion where you might need to connect the output from one {{PS1}} to another {{PS1}} ~~here~~ are some ways to approach it.

<table><tr><td>__TOC__</td><td>On the relatively rare occasion where you might need to connect the output from one {{PS1}} to another {{PS1}}.

Here are some ways to approach it.

</td></tr></table>

=== Two {{PS1}}s for one Vocal ===

You can

* Run your microphone into the first ~~L1™~~ PS1 Powerstand (let's say - Channel 1).

* Run your microphone into the first {{l1 nl}} PS1 Powerstand (let's say - Channel 1).

* In Channel 1 ~~insert~~ an XLR cable from the Channel 1 Line Out

* In the Channel 1 section run an XLR cable from the Channel 1 Line Out

* At the other end of the cable connect a [[Pad]]. The people-at-Bose usually recommend a -20 dBu pad. Some owners have reported success with a -10 dBu pad.

** {{Why Use a -20 dB Pad}}

* Connect the [[Pad]] to the second {{PS1}} Channel 1 or 2.

* On the first {{PS1}}, set the input trim appropriately.

Line 24:

Line 28:

You can

* Run your input into the first L1™ PS1 Powerstand (let's say - Channel 2).

* In Channel 2 ~~insert~~ an XLR cable from the Channel 2 Line Out

* In Channel 2 section run an XLR cable from the Channel 2 Line Out

* At the other end of the cable connect a [[Pad]]. The people-at-Bose usually recommend a -20 dBu pad. Some owners have reported success with a -10 dBu pad.

** {{Why Use a -20 dB Pad}}

* Connect the [[Pad]] to the second {{PS1}} Channel 2.

* On the first {{PS1}}, set the input trim appropriately.

Line 36:

Line 41:

* [[PS1 Powerstand Connections/Interactive|Close up view of the Input Panel]]

=== XLR Female to ¼ Inch Tip-Sleeve Male ===

Here is another method - use a cable with a XLR Female to ¼ Inch Tip-Sleeve Male from a Powerstand Line OUT to Channels 1, 2, 3 or 4 on a second Powerstand.

[[Image:XlrFtxM.png]]

----

[[category:PS1 Powerstand]]

[[~~category~~:~~L1™~~ System]]

[[Category:L1® System]]

[[Category:Daisy Chain]]

@@ Line 1: / Line 1: @@
-<table><tr><td>__TOC__</td><td>On the relatively rare occasion where you might need to connect the output from one {{PS1}} to another {{PS1}} here are some ways to approach it.
+{{Model I icon}}{{Classic icon}}
+<table><tr><td>__TOC__</td><td>On the relatively rare occasion where you might need to connect the output from one {{PS1}} to another {{PS1}}.
+Here are some ways to approach it.
 </td></tr></table>
 === Two {{PS1}}s for one Vocal ===
 You can
-* Run your microphone into the first L1™ PS1 Powerstand (let's say - Channel 1).
+* Run your microphone into the first {{l1 nl}} PS1 Powerstand (let's say - Channel 1).
-* In Channel 1 insert an XLR cable from the Channel 1 Line Out
+* In the Channel 1 section run an XLR cable from the Channel 1 Line Out
 * At the other end of the cable connect a [[Pad]]. The people-at-Bose usually recommend a -20 dBu pad. Some owners have reported success with a -10 dBu pad.
+** {{Why Use a -20 dB Pad}}
 * Connect the [[Pad]] to the second {{PS1}} Channel 1 or 2.
 * On the first {{PS1}}, set the input trim appropriately.
@@ Line 24: / Line 28: @@
 You can
 * Run your input into the first L1™ PS1 Powerstand (let's say - Channel 2).
-* In Channel 2 insert an XLR cable from the Channel 2 Line Out
+* In Channel 2 section run an XLR cable from the Channel 2 Line Out
 * At the other end of the cable connect a [[Pad]]. The people-at-Bose usually recommend a -20 dBu pad. Some owners have reported success with a -10 dBu pad.
+** {{Why Use a -20 dB Pad}}
 * Connect the [[Pad]] to the second {{PS1}} Channel 2.
 * On the first {{PS1}}, set the input trim appropriately.
@@ Line 36: / Line 41: @@
 * [[PS1 Powerstand Connections/Interactive|Close up view of the Input Panel]]
+=== XLR Female to ¼ Inch Tip-Sleeve Male ===
+Here is another method - use a cable with a XLR Female to ¼ Inch Tip-Sleeve Male from a Powerstand Line OUT to Channels 1, 2, 3 or 4 on a second Powerstand.
+[[Image:XlrFtxM.png]]
 ----
 <references/>
 [[category:PS1 Powerstand]]
-[[category:L1™ System]]
+[[Category:L1® System]]
+[[Category:Daisy Chain]]