External Subwoofers: Difference between revisions

(8 intermediate revisions by the same user not shown)

Line 1:

~~== External Subs==~~

=== Passive (unpowered) Loudspeakers ===

Using loudspeakers other than the {{B1}} with any of the {{L1}} systems is not supported. However you can safely try your own external subs if the impedance is no lower then 4 ohms (typically a single 4 ohm loudspeaker or two 8 ohm loudspeakers in parallel). The output from the Power Stand is 250 watts RMS into 4 ohms.

Using loudspeakers other than the {{B1}} with any of the {{L1 nl}} systems is not supported. However you can safely try your own external subs if the impedance is no lower then 4 ohms (typically a single 4 ohm loudspeaker or two 8 ohm loudspeakers in parallel). The output from the Power Stand is 250 watts RMS into 4 ohms.

==== {{Classic nl}} and {{Model I nl}}====

{{~~#lst~~:PS1 Power Stand / Bass Line Out~~|Bass Module Output}}~~

For the sake of those attaching third party passive speakers (an unsupported application).

Output if no {{B1}}s detected

* 40-{{{Crossover|180}}} Hz Bandpass (that is: NO B1 EQ)

If one or two {{B1}}s detected (or resistors used across NL4 2+ / 2- pins to emulate detection)

* 40-{{{Crossover|180}}} Hz with different EQ curves. For details on how to do this see: [[Activating B1 EQ Curves]]

For more details about the Power Stand outputs see: [[PS1 Power Stand / Bass Line Out]]

==== {{Model II nl}}====

{{~~#lst~~:L1® Model II Power Stand / Bass Line Out~~|Bass Module Output}}~~

For the sake of those attaching third party passive speakers (an unsupported application).

Output if no {{B1}}s detected

* 40-{{{Crossover|200}}} Hz Bandpass (that is: NO B1 EQ)

If one or two {{B1}}s detected (or resistors used across NL4 2+ / 2- pins to emulate detection)

* 40-{{{Crossover|200}}} Hz with different EQ curves. For details on how to do this see: [[Activating B1 EQ Curves]]

For more details about the Power Stand outputs see: [[L1® Model II Power Stand / Bass Line Out]]

=== Active (powered) Loudspeakers===

~~Using powered loudspeakers with any of the~~ {{~~L1 nl~~}} ~~systems is not supported. The [[PackLite® power amplifier Model A1]] is part the~~ {{~~l1 nl~~}} ~~System. It can be used to power up to two~~ {{B1}}~~s. This is connected to~~ the ~~Power Stand Bass Line Out (applies to~~ {{~~Classic nl}}, {{Model I nl}}, {{Model II~~ nl}}.

Using powered loudspeakers with any of the {{L1 nl}} systems is not supported.

==== [[PackLite® power amplifier Model A1]] ====

The [[PackLite® power amplifier Model A1]] is part the {{l1 nl}} System. It can be used to power up to two {{B1}}s. This is connected to the Power Stand Bass Line Out.

==== Third Party (non-{{Bose}}) Systems ====

If you want to use a powered loudspeaker system, you can use the Power Stand Bass Line Out as the signal source. Here are notes specific to the {{L1 nl}} you are using.

Line 22:

Line 45:

Please see [[PackLite® power amplifier Model A1]] for extensive notes that include ideas that can be applied to other systems.

== Ongoing discussion ==

[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/178108737 I need more bass article - discussion]

----

[[Category:Bass]]

[[Category:Unsupported Applications]]

@@ Line 1: / Line 1: @@
-== External Subs==
 === Passive (unpowered) Loudspeakers ===
 {{Classic icon}}{{Model I icon}}{{Model II icon}}
-Using loudspeakers other than the {{B1}} with any of the {{L1}} systems is not supported. However you can safely try your own external subs if the impedance is no lower then 4 ohms (typically a single 4 ohm loudspeaker or two 8 ohm loudspeakers in parallel). The output from the Power Stand is 250 watts RMS into 4 ohms.
+Using loudspeakers other than the {{B1}} with any of the {{L1 nl}} systems is not supported. However you can safely try your own external subs if the impedance is no lower then 4 ohms (typically a single 4 ohm loudspeaker or two 8 ohm loudspeakers in parallel). The output from the Power Stand is 250 watts RMS into 4 ohms.
 ==== {{Classic nl}} and {{Model I nl}}====
-{{#lst:PS1 Power Stand / Bass Line Out|Bass Module Output}}
+{{Classic icon}}{{Model I icon}}
+For the sake of those attaching third party passive speakers (an unsupported application).
+Output if no {{B1}}s detected
+* 40-{{{Crossover|180}}} Hz Bandpass (that is: NO B1 EQ)
+If one or two {{B1}}s detected (or resistors used across NL4 2+ / 2- pins to emulate detection)
+* 40-{{{Crossover|180}}} Hz with different EQ curves. For details on how to do this see: [[Activating B1 EQ Curves]]
+For more details about the Power Stand outputs see: [[PS1 Power Stand / Bass Line Out]]
 ==== {{Model II nl}}====
-{{#lst:L1® Model II Power Stand / Bass Line Out|Bass Module Output}}
+{{Model II icon}}
+For the sake of those attaching third party passive speakers (an unsupported application).
+Output if no {{B1}}s detected
+* 40-{{{Crossover|200}}} Hz Bandpass (that is: NO B1 EQ)
+If one or two {{B1}}s detected (or resistors used across NL4 2+ / 2- pins to emulate detection)
+* 40-{{{Crossover|200}}} Hz with different EQ curves. For details on how to do this see: [[Activating B1 EQ Curves]]
+For more details about the Power Stand outputs see: [[L1® Model II Power Stand / Bass Line Out]]
 === Active (powered) Loudspeakers===
-Using powered loudspeakers with any of the {{L1 nl}} systems is not supported. The [[PackLite® power amplifier Model A1]] is part the {{l1 nl}} System. It can be used to power up to two {{B1}}s. This is connected to the Power Stand Bass Line Out (applies to {{Classic nl}}, {{Model I nl}}, {{Model II nl}}.
+{{Classic icon}}{{Model I icon}}{{Model II icon}}
+Using powered loudspeakers with any of the {{L1 nl}} systems is not supported.
+==== [[PackLite® power amplifier Model A1]] ====
+The [[PackLite® power amplifier Model A1]] is part the {{l1 nl}} System. It can be used to power up to two {{B1}}s. This is connected to the Power Stand Bass Line Out.
+==== Third Party (non-{{Bose}}) Systems ====
 If you want to use a powered loudspeaker system, you can use the Power Stand Bass Line Out as the signal source. Here are notes specific to the {{L1 nl}} you are using.
@@ Line 22: / Line 45: @@
 Please see [[PackLite® power amplifier Model A1]] for extensive notes that include ideas that can be applied to other systems.
+== Ongoing discussion ==
+[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/178108737 I need more bass article - discussion]
+----
+[[Category:Bass]]
+[[Category:Unsupported Applications]]