Using a Different Sub - Revision history

ST at 15:33, 20 February 2013

2013-02-20T15:33:34Z

← Older revision		Revision as of 15:33, 20 February 2013
Line 1:		Line 1:
	~~'''Using a Different Sub'''~~
	{{Classic icon}} {{Model I icon}}		{{Classic icon}} {{Model I icon}}

Line 7:		Line 6:
	These predate the {{Model II}} but are largely applicable. Note: The crossover point for the Model II is 200 Hz rather than 180 Hz documented below for the {{Classic}} and {{Model I}}. On the {{Model II}} the crossover point is fixed at 200 Hz and does not change regardless of whether or not there are B1s attached to the Power Stand.		These predate the {{Model II}} but are largely applicable. Note: The crossover point for the Model II is 200 Hz rather than 180 Hz documented below for the {{Classic}} and {{Model I}}. On the {{Model II}} the crossover point is fixed at 200 Hz and does not change regardless of whether or not there are B1s attached to the Power Stand.

			=== What are the benefits of using a different sub ===
	~~'''Question'''~~		What are the problems or benefits of plugging in a different sub cabinet to the L1® (Classic/Model I). It it even possible or feasible. Say you have a 4 ohm 250 watt EV sub with a 15 inch speaker and you plugged into it instead of the B1. What could you expect and is there any possible damage you could cause.

	:What are the problems or benefits of plugging in a different sub cabinet to the ~~PAS~~. It it even possible or feasible. Say you have a 4 ohm 250 watt EV sub with a 15 inch speaker and you plugged into it instead of the B1. What could you expect and is there any possible damage you could cause.
	or could you use that instead of a second B1 for more bottom.		or could you use that instead of a second B1 for more bottom.

	Breaking this down into several smaller questions we get:		Breaking this down into several smaller questions we get:

	;Can you cause any damage to the Power Stand or the speakers by using a third-party loudspeaker?		===Can you cause any damage to the Power Stand or the speakers by using a third-party loudspeaker?===

	A: The powered Bass Output of the Power Stand is rated to provide		The powered Bass Output of the Power Stand is rated to provide
	* 125 Watts at 8 ohms		* 125 Watts at 8 ohms
	* 250 Watts at 4 ohms		* 250 Watts at 4 ohms
Line 23:		Line 20:
	Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the {{Classic}}, this connection is called Amp3 Out, and in later versions that connection has a blue background.		Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the {{Classic}}, this connection is called Amp3 Out, and in later versions that connection has a blue background.

	;What is the Crossover Point for the powered Power Stand Bass Output?		===What is the Crossover Point for the powered Power Stand Bass Output? ===

	A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.		This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
	* '''110''' Hz when there are no B1 Bass Modules connected to the Power Stand Bass Output.		* '''110''' Hz when there are no B1 Bass Modules connected to the Power Stand Bass Output.
	* '''180''' Hz if there is a loudspeaker (B1, B2, or third party) attached.		* '''180''' Hz if there is a loudspeaker (B1, B2, or third party) attached.
Line 31:		Line 28:
	* '''180''' Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.		* '''180''' Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.

	;What is the Frequency for the unpowered Power Stand Bass Line Out?		===What is the Frequency for the unpowered Power Stand Bass Line Out? ===

	A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.		This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
	* '''40-180Hz''' Band Pass when no {{B1}}s are attached to the Power Stand		* '''40-180Hz''' Band Pass when no {{B1}}s are attached to the Power Stand
	* '''40-180Hz''' If any {{B1}}s are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are {{B1}}s connected directly to the Power Stand, the the Bass Line Out is optimized for ''more'' {{B1}}s as would be appropriate when using the {{A1 EB}}.		* '''40-180Hz''' If any {{B1}}s are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are {{B1}}s connected directly to the Power Stand, the the Bass Line Out is optimized for ''more'' {{B1}}s as would be appropriate when using the {{A1 EB}}.

	;Can I mix {{B1}}s with other subs?		===Can I mix {{B1}}s with other subs?===

			This is not recommended. <ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/1506041054/m/717103866?r=364104966#364104966 mixing subs with B1s not recommended]</ref>

	~~A: This is not recommended. <ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/1506041054/m/717103866?r=364104966#364104966 mixing subs with B1s not recommended]</ref>~~

			===Why does Bose call the B1 a Bass Module instead of a sub===

	~~;Why does Bose call~~ the ~~B1 a Bass Module instead of a sub.~~		Here is the story as far as I can tell:

	~~A: Here is the story as far as I can tell:~~
	Originally the term "subwoofer" was used in movie theater sound systems. There the standard is still 5 full-range channels and one subwoofer channel. The subwoofer channel has signifcant spectral overlap with the main channels. Typically the main channels start at 40 Hz or 50 Hz and the subwoofer ranges from 30ish up to about 120 Hz. The Subwoofer can produce some serious bass level, but fidelity is not much of an requirement, as they are mainly used for sound effects (explosion, the ominous rumble, etc.)		Originally the term "subwoofer" was used in movie theater sound systems. There the standard is still 5 full-range channels and one subwoofer channel. The subwoofer channel has signifcant spectral overlap with the main channels. Typically the main channels start at 40 Hz or 50 Hz and the subwoofer ranges from 30ish up to about 120 Hz. The Subwoofer can produce some serious bass level, but fidelity is not much of an requirement, as they are mainly used for sound effects (explosion, the ominous rumble, etc.)

ST: formatting

2013-02-20T15:26:10Z

formatting

ST at 15:23, 20 February 2013

2013-02-20T15:23:59Z

← Older revision		Revision as of 15:23, 20 February 2013
Line 26:		Line 26:

	A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.		A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
	* '''110''' Hz when there are no B1 Bass Modules connected to the Power Stand Bass Output.		* '''110''' Hz when there are no B1 Bass Modules connected to the Power Stand Bass Output.
			* '''180''' Hz if there is a loudspeaker (B1, B2, or third party) attached.
	* '''180''' Hz if there is something (even a dummy plug) is inserted into the Bass Line Out jack on the Power Stand.		* '''180''' Hz if there is something (even a dummy plug) is inserted into the Bass Line Out jack on the Power Stand.
	* '''180''' Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.		* '''180''' Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.

ST at 16:28, 3 June 2008

2008-06-03T16:28:41Z

← Older revision		Revision as of 16:28, 3 June 2008
Line 5:		Line 5:
	[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6401018152?r=2741042352#2741042352 Using a Different Sub] (October 2005). These are still applicable to the {{Classic}} and {{Model I}}.		[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6401018152?r=2741042352#2741042352 Using a Different Sub] (October 2005). These are still applicable to the {{Classic}} and {{Model I}}.

	These predate the {{Model II}} but are largely applicable. Note: The crossover point for the Model II is 200 Hz rather than 180 Hz documented below for the {{Classic}} and {{Model I}}.		These predate the {{Model II}} but are largely applicable. Note: The crossover point for the Model II is 200 Hz rather than 180 Hz documented below for the {{Classic}} and {{Model I}}. On the {{Model II}} the crossover point is fixed at 200 Hz and does not change regardless of whether or not there are B1s attached to the Power Stand.

ST at 16:27, 3 June 2008

2008-06-03T16:27:21Z

ST at 16:22, 3 June 2008

2008-06-03T16:22:47Z

← Older revision		Revision as of 16:22, 3 June 2008
Line 3:		Line 3:

	The following notes are compiled from a discussion on the Bose Community Message Boards.		The following notes are compiled from a discussion on the Bose Community Message Boards.
	[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6401018152?r=2741042352#2741042352 Using a Different Sub]		[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6401018152?r=2741042352#2741042352 Using a Different Sub] (October 2005). These are still applicable to the {{Classic}} and {{Model I}}.

	These predate the {{Model II}} but are largely applicable. Note: The crossover point for the Model II is 200 Hz rather than 180 Hz documented below for the {{Classic}} and {{Model I}}.		These predate the {{Model II}} but are largely applicable. Note: The crossover point for the Model II is 200 Hz rather than 180 Hz documented below for the {{Classic}} and {{Model I}}.

ST: applicabilility of Model II

2008-06-03T16:21:06Z

applicabilility of Model II

← Older revision		Revision as of 16:21, 3 June 2008
Line 1:		Line 1:
	Using a Different Sub		'''Using a Different Sub'''
			{{Classic icon}} {{Model I icon}}

	The following notes are compiled from a discussion on the Bose Community Message Boards.		The following notes are compiled from a discussion on the Bose Community Message Boards.
	[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6401018152?r=2741042352#2741042352 Using a Different Sub]		[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6401018152?r=2741042352#2741042352 Using a Different Sub]

			These predate the {{Model II}} but are largely applicable. Note: The crossover point for the Model II is 200 Hz rather than 180 Hz documented below for the {{Classic}} and {{Model I}}.

	Question
			'''Question'''

	:What are the problems or benefits of pluging in a different sub cabinet to the PAS. It it even possible or feasible. Say you have a 4 ohm 250 watt EV sub with a 15 inch speaker and you plugged into it instead of the B1. What could you expect and is there any possible damage you could cause.		:What are the problems or benefits of pluging in a different sub cabinet to the PAS. It it even possible or feasible. Say you have a 4 ohm 250 watt EV sub with a 15 inch speaker and you plugged into it instead of the B1. What could you expect and is there any possible damage you could cause.

ST: spelling

2007-10-16T09:05:11Z

spelling

← Older revision		Revision as of 09:05, 16 October 2007
Line 7:		Line 7:
	Question		Question

	:What are the problems or benefits of pluging in a different sub cabinet to the PAS. It it even possible or ~~feasable~~. Say you have a 4 ohm 250 watt EV sub with a 15 in speaker and you ~~pluged~~ into it instead of the B1. What could you expect and is there any possible damage you could cause.		:What are the problems or benefits of pluging in a different sub cabinet to the PAS. It it even possible or feasible. Say you have a 4 ohm 250 watt EV sub with a 15 inch speaker and you plugged into it instead of the B1. What could you expect and is there any possible damage you could cause.
	or could you use that instead of a second B1 for more bottom.		or could you use that instead of a second B1 for more bottom.

ST: first ed

2007-10-16T07:55:01Z

first ed

New page

Using a Different Sub

The following notes are compiled from a discussion on the Bose Community Message Boards.
[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6401018152?r=2741042352#2741042352 Using a Different Sub]

Question

:What are the problems or benefits of pluging in a different sub cabinet to the PAS. It it even possible or feasable. Say you have a 4 ohm 250 watt EV sub with a 15 in speaker and you pluged into it instead of the B1. What could you expect and is there any possible damage you could cause.
or could you use that instead of a second B1 for more bottom.

Breaking this down into several smaller questions we get:

Q: Can you cause any damage to the Power Stand or the speakers by using a third-party loudspeaker?

A: The powered Bass Output of the Power Stand is rated to provide
* 125 Watts at 8 ohms
* 250 Watts at 4 ohms

Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the L1™ Classic, this connection is called Amp3 Out, and in later versions that connection has a blue background.

Q: What is the Crossover Point for the powered Power Stand Bass Output?

A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
* '''110''' Hz when there are no B1 Bass Modules connected to the Power Stand Bass Output.
* '''180''' Hz if there is something (even a dummy plug) is inserted into the Bass Line Out jack on the Power Stand.
* '''180''' Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.

Q: What is the Frequency for the unpowered Power Stand Bass Line Out?

A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
* '''40-180Hz''' Band Pass when no {{B1}}s are attached to the Power Stand
* '''40-180Hz''' If any {{B1}}s are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are {{B1}}s connecte directly to the Power Stand, the the Bass Line Out is optimized for ''more'' {{B1}}s as would be appropriate when using the {{A1 EB}}.

Q: Can I mix {{B1}}s with other subs?

A: This is not recommended. <ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/1506041054/m/717103866?r=364104966#364104966 mixing subs with B1s not recommended]</ref>

Q: Why does Bose call the B1 a Bass Module instead of a sub.

A: Here is the story as far as I can tell:
Originally the term "subwoofer" was used in movie theater sound systems. There the standard is still 5 full-range channels and one subwoofer channel. The subwoofer channel has signifcant spectral overlap with the main channels. Typically the main channels start at 40 Hz or 50 Hz and the subwoofer ranges from 30ish up to about 120 Hz. The Subwoofer can produce some serious bass level, but fidelity is not much of an requirement, as they are mainly used for sound effects (explosion, the ominous rumble, etc.)

In contrast a multi-way PA of the time had between 2 and 4 different speakers all dedicated to specific non-overlapping frequency areas. The bass produces were typically called bass-bins or bass cabinets and not subwoofers, as they actually do something different.

Bose was probably one of the first (if not the first), that made the split system (single bass box, multiple small satelite) commercially successful for home use with the AM-5 speaker. As commonplace as it is today, at the time it was a pretty radical idea and many, many audio experts stated that can't possibly work (sounds familiar ?). Anyway, as we tried to name the black bass-producing device, we felt bass module was a good choice as it was functionally different from a subwoofer.

After it turned out, that the concept did indeed work many more manufactures turned out products in the same category and in the process subwoofer became the common term. Maybe the marketing departments wanted to imply that it's similar to a real movie sound system, maybe they just didn't know the difference.

So in short, IMO the difference would be
a) Subwoofer is a low frequency extension, but the system can also work without it
b) Bass module is a integral part of the system with dedicated non-overlapping frequecny range.

Of course, in the end it's just nit-picking and common use defines language more than any technical specification.

Just my 2c

Hilmar<ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/3391015572?r=2461077572#2461077572 talking about subwoofers and bass modules.]</ref>

<noinclude>
----
<references/>
[[Category:A1 PackLite®]]
[[Category:PS1 Powerstand]]
[[Category:Bass]]
[[Category:B1 Bass Module]]
</noinclude>

← Older revision		Revision as of 15:26, 20 February 2013
Line 15:		Line 15:
	Breaking this down into several smaller questions we get:		Breaking this down into several smaller questions we get:

	Q: Can you cause any damage to the Power Stand or the speakers by using a third-party loudspeaker?		;Can you cause any damage to the Power Stand or the speakers by using a third-party loudspeaker?

	A: The powered Bass Output of the Power Stand is rated to provide		A: The powered Bass Output of the Power Stand is rated to provide
Line 23:		Line 23:
	Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the {{Classic}}, this connection is called Amp3 Out, and in later versions that connection has a blue background.		Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the {{Classic}}, this connection is called Amp3 Out, and in later versions that connection has a blue background.

	Q: What is the Crossover Point for the powered Power Stand Bass Output?		;What is the Crossover Point for the powered Power Stand Bass Output?

	A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.		A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
Line 31:		Line 31:
	* '''180''' Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.		* '''180''' Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.

	Q: What is the Frequency for the unpowered Power Stand Bass Line Out?		;What is the Frequency for the unpowered Power Stand Bass Line Out?

	A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.		A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
Line 37:		Line 37:
	* '''40-180Hz''' If any {{B1}}s are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are {{B1}}s connected directly to the Power Stand, the the Bass Line Out is optimized for ''more'' {{B1}}s as would be appropriate when using the {{A1 EB}}.		* '''40-180Hz''' If any {{B1}}s are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are {{B1}}s connected directly to the Power Stand, the the Bass Line Out is optimized for ''more'' {{B1}}s as would be appropriate when using the {{A1 EB}}.

	Q: Can I mix {{B1}}s with other subs?		;Can I mix {{B1}}s with other subs?

	A: This is not recommended. <ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/1506041054/m/717103866?r=364104966#364104966 mixing subs with B1s not recommended]</ref>		A: This is not recommended. <ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/1506041054/m/717103866?r=364104966#364104966 mixing subs with B1s not recommended]</ref>


	Q: Why does Bose call the B1 a Bass Module instead of a sub.		;Why does Bose call the B1 a Bass Module instead of a sub.

	A: Here is the story as far as I can tell:		A: Here is the story as far as I can tell:
Line 53:		Line 53:
	After it turned out, that the concept did indeed work many more manufactures turned out products in the same category and in the process subwoofer became the common term. Maybe the marketing departments wanted to imply that it's similar to a real movie sound system, maybe they just didn't know the difference.		After it turned out, that the concept did indeed work many more manufactures turned out products in the same category and in the process subwoofer became the common term. Maybe the marketing departments wanted to imply that it's similar to a real movie sound system, maybe they just didn't know the difference.

	So in short, ~~IMO~~ the difference would be		So in short, in my opinion the difference would be
	a) Subwoofer is a low frequency extension, but the system can also work without it		<br />a) Subwoofer is a low frequency extension, but the system can also work without it
	b) Bass module is a integral part of the system with dedicated non-overlapping frequecny range.		<br />b) Bass module is a integral part of the system with dedicated non-overlapping frequecny range.

	Of course, in the end it's just nit-picking and common use defines language more than any technical specification.		Of course, in the end it's just nit-picking and common use defines language more than any technical specification.

← Older revision		Revision as of 16:27, 3 June 2008
Line 10:		Line 10:
	'''Question'''		'''Question'''

	:What are the problems or benefits of ~~pluging~~ in a different sub cabinet to the PAS. It it even possible or feasible. Say you have a 4 ohm 250 watt EV sub with a 15 inch speaker and you plugged into it instead of the B1. What could you expect and is there any possible damage you could cause.		:What are the problems or benefits of plugging in a different sub cabinet to the PAS. It it even possible or feasible. Say you have a 4 ohm 250 watt EV sub with a 15 inch speaker and you plugged into it instead of the B1. What could you expect and is there any possible damage you could cause.
	or could you use that instead of a second B1 for more bottom.		or could you use that instead of a second B1 for more bottom.

Line 21:		Line 21:
	* 250 Watts at 4 ohms		* 250 Watts at 4 ohms

	Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the ~~L1™~~ Classic, this connection is called Amp3 Out, and in later versions that connection has a blue background.		Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the {{Classic}}, this connection is called Amp3 Out, and in later versions that connection has a blue background.

	Q: What is the Crossover Point for the powered Power Stand Bass Output?		Q: What is the Crossover Point for the powered Power Stand Bass Output?
Line 34:		Line 34:
	A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.		A: This depends on if there are if there are {{B1}}s attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.
	* '''40-180Hz''' Band Pass when no {{B1}}s are attached to the Power Stand		* '''40-180Hz''' Band Pass when no {{B1}}s are attached to the Power Stand
	* '''40-180Hz''' If any {{B1}}s are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are {{B1}}s ~~connecte~~ directly to the Power Stand, the the Bass Line Out is optimized for ''more'' {{B1}}s as would be appropriate when using the {{A1 EB}}.		* '''40-180Hz''' If any {{B1}}s are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are {{B1}}s connected directly to the Power Stand, the the Bass Line Out is optimized for ''more'' {{B1}}s as would be appropriate when using the {{A1 EB}}.

	Q: Can I mix {{B1}}s with other subs?		Q: Can I mix {{B1}}s with other subs?
Line 48:		Line 48:
	In contrast a multi-way PA of the time had between 2 and 4 different speakers all dedicated to specific non-overlapping frequency areas. The bass produces were typically called bass-bins or bass cabinets and not subwoofers, as they actually do something different.		In contrast a multi-way PA of the time had between 2 and 4 different speakers all dedicated to specific non-overlapping frequency areas. The bass produces were typically called bass-bins or bass cabinets and not subwoofers, as they actually do something different.

	Bose was probably one of the first (if not the first), that made the split system (single bass box, multiple small ~~satelite~~) commercially successful for home use with the AM-5 speaker. As commonplace as it is today, at the time it was a pretty radical idea and many, many audio experts stated that can't possibly work (sounds familiar ?). Anyway, as we tried to name the black bass-producing device, we felt bass module was a good choice as it was functionally different from a subwoofer.		Bose was probably one of the first (if not the first), that made the split system (single bass box, multiple small satellite) commercially successful for home use with the AM-5 speaker. As commonplace as it is today, at the time it was a pretty radical idea and many, many audio experts stated that can't possibly work (sounds familiar ?). Anyway, as we tried to name the black bass-producing device, we felt bass module was a good choice as it was functionally different from a subwoofer.

	After it turned out, that the concept did indeed work many more manufactures turned out products in the same category and in the process subwoofer became the common term. Maybe the marketing departments wanted to imply that it's similar to a real movie sound system, maybe they just didn't know the difference.		After it turned out, that the concept did indeed work many more manufactures turned out products in the same category and in the process subwoofer became the common term. Maybe the marketing departments wanted to imply that it's similar to a real movie sound system, maybe they just didn't know the difference.