Template:ToneMatch Mixers to F1 Model 812 - Revision history

ST at 07:06, 12 April 2019

2019-04-12T07:06:21Z

← Older revision		Revision as of 07:06, 12 April 2019
Line 3:		Line 3:
	#Power on the devices.		#Power on the devices.
	#Set the F1 812 switch to Line Level and turn up the Volume knob to the 12 o’clock center detent.		#Set the F1 812 switch to Line Level and turn up the Volume knob to the 12 o’clock center detent.
	#Set the ToneMatch mixer Master output to 10 o’clock. <!-- This is the mixer’s unity output.-->		#Set the ToneMatch mixer Master output to 10 o’clock. --> <!-- This is the mixer’s unity output.--> <!--
	#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs \| Input Level on the ToneMatch mixer to monitor the input level.		#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs \| Input Level on the ToneMatch mixer to monitor the input level.
	#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs \| Output Level on the ToneMatch mixer.		#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs \| Output Level on the ToneMatch mixer.

ST at 07:02, 12 April 2019

2019-04-12T07:02:29Z

@@ Line 1: / Line 1: @@
 #Plug in your ToneMatch mixer and F1 812 to power and then connect the audio path using an XLR or TRS ¼-inch cable.
 #Power on the devices.
@@ Line 5: / Line 6: @@
 #Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs | Input Level on the ToneMatch mixer to monitor the input level.
 #Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs | Output Level on the ToneMatch mixer.
 ----

ST at 22:38, 3 February 2019

2019-02-03T22:38:14Z

← Older revision		Revision as of 22:38, 3 February 2019
Line 3:		Line 3:
	#Set the F1 812 switch to Line Level and turn up the Volume knob to the 12 o’clock center detent.		#Set the F1 812 switch to Line Level and turn up the Volume knob to the 12 o’clock center detent.
	#Set the ToneMatch mixer Master output to 10 o’clock. <!-- This is the mixer’s unity output.-->		#Set the ToneMatch mixer Master output to 10 o’clock. <!-- This is the mixer’s unity output.-->
	#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs � Input Level on the ToneMatch mixer to monitor the input level.		#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs \| Input Level on the ToneMatch mixer to monitor the input level.
	#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs � Output Level on the ToneMatch mixer.		#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs \| Output Level on the ToneMatch mixer.

	----		----

ST: Created page with "#Plug in your ToneMatch mixer and F1 812 to power and then connect the audio path using an XLR or TRS ¼-inch cable. #Power on the devices. #Set the F1 812 switch to Line Leve..."

2019-02-03T22:34:22Z

Created page with "#Plug in your ToneMatch mixer and F1 812 to power and then connect the audio path using an XLR or TRS ¼-inch cable. #Power on the devices. #Set the F1 812 switch to Line Leve..."

New page

#Plug in your ToneMatch mixer and F1 812 to power and then connect the audio path using an XLR or TRS ¼-inch cable.
#Power on the devices.
#Set the F1 812 switch to Line Level and turn up the Volume knob to the 12 o’clock center detent.
#Set the ToneMatch mixer Master output to 10 o’clock. 
#Set ToneMatch Trim controls and set the input volumes as high as possible without input clipping. You can use the Prefs � Input Level on the ToneMatch mixer to monitor the input level.
#Unmute the channels on the ToneMatch mixer and adjust your channel volumes to stay between 0 dB and +6 dB at the master output. You can monitor this visually on the T8S LED or in the Prefs � Output Level on the ToneMatch mixer.

----
[[Category:F1]]
[[Category:T4S]]
[[Category:T8S]]