Template:T4S/T8S Mono Output - Revision history

ST: /* T8S ToneMatch® mixer */

2024-02-12T22:46:49Z

T8S ToneMatch® mixer

← Older revision		Revision as of 22:46, 12 February 2024
Line 18:		Line 18:

	===T8S ToneMatch® mixer===		===T8S ToneMatch® mixer===
			; If connecting to the ToneMatch port to an L1 Pro (any model)
			* Pan all inputs hard LEFT
			; Note: Anything panned hard RIGHT will not be heard at the ToneMatch Output to the L1 Pro

			; If using the analog outputs (XLR or 1/4 inch (6.3 mm) Tip-Ring-Sleeve)
	*Pan all inputs hard RIGHT		*Pan all inputs hard RIGHT
	*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable		*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable

ST at 16:09, 6 November 2019

2019-11-06T16:09:19Z

← Older revision		Revision as of 16:09, 6 November 2019
Line 29:		Line 29:

	=== Mono using Aux Output ===		=== Mono using Aux Output ===
	You can create a summed mono output by directing your input channels (1-4 or 1-8) to an Aux Output. See [[~~{{PAGENAME}}~~#Aux Outputs\|Aux Outputs]] for details.		You can create a summed mono output by directing your input channels (1-4 or 1-8) to an Aux Output. See [[T4S/T8S_ToneMatch®_Mixer#Aux Outputs\|Aux Outputs]] for details.

ST: Created page with "== Mono Output == On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO). ;Please note: There is no hardwired summed mono output on the Ton..."

2019-11-06T16:01:43Z

Created page with "== Mono Output == On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO). ;Please note: There is no hardwired summed mono output on the Ton..."

New page

== Mono Output ==
On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO).
;Please note: There is no hardwired summed mono output on the ToneMatch mixers. Any input signal that is panned hard Left will not be heard through the Right output. To get a mono output please see below.

=== General Information ===
As you move the pan control away from the center, the sound level increases slightly in one direction and decreases in the other. If you pan inputs hard to one side (e.g., Right) and the Right output will be slightly louder (theoretically, up to +3 dB louder) than if you had panned the inputs up the middle. And panned hard Right - there will be no signal at the Left Output.

===T4S ToneMatch® mixer===

*Pan all inputs hard RIGHT
*Connect your L1® to the RIGHT ToneMatch® port

OR

*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable.

;Note: Anything panned hard LEFT will not be heard at the RIGHT Output.

===T8S ToneMatch® mixer===

*Pan all inputs hard RIGHT
*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable

OR

*Use the XLR Right Output to powered a loudspeaker (e.g. S1 Pro, F1 Model 812). or L1® Compact with XLR to ¼ inch (6mm) jack Tip-Ring-Sleeve.

;Note: Anything panned hard LEFT will not be heard at the RIGHT Output.

=== Mono using Aux Output ===
You can create a summed mono output by directing your input channels (1-4 or 1-8) to an Aux Output. See [[{{PAGENAME}}#Aux Outputs|Aux Outputs]] for details.