Template:T1 ToneMatch® Audio Engine to Two L1®s - Revision history

ST at 15:57, 18 June 2018

2018-06-18T15:57:22Z

← Older revision		Revision as of 15:57, 18 June 2018
Line 38:		Line 38:
	# Connect the T1 Master Output to the Analog Input using a 1/4 inch (6mm) Tip-Ring-Sleeve cable		# Connect the T1 Master Output to the Analog Input using a 1/4 inch (6mm) Tip-Ring-Sleeve cable
	# Adjust the volume of the audio source to the maximum output without distortion.		# Adjust the volume of the audio source to the maximum output without distortion.
	# While playing the ~~source~~, increase the '''Trim''' level so that the '''Signal/Clip''' indicator glows green or yellow.		# While playing music through the T1®, increase the '''Trim''' level so that the '''Signal/Clip''' indicator glows green or yellow.
	# If the '''Signal/Clip''' indicator glows red, decrease the '''Trim''' level so that it glows only green or yellow.		# If the '''Signal/Clip''' indicator glows red, decrease the '''Trim''' level so that it glows only green or yellow.

ST: trim setting for analog input

2018-06-18T15:56:00Z

trim setting for analog input

@@ Line 29: / Line 29: @@
 </td></tr>
 </table>
 ==Stereo ==

ST: ST moved page Template:T1 ToneMatchÂ® Audio Engine to Two L1Â®s to Template:T1 ToneMatch® Audio Engine to Two L1®s

2017-03-26T07:58:18Z

ST moved page Template:T1 ToneMatchÂ® Audio Engine to Two L1Â®s to Template:T1 ToneMatch® Audio Engine to Two L1®s

← Older revision	Revision as of 07:58, 26 March 2017
(No difference)

ST at 20:01, 8 February 2014

2014-02-08T20:01:29Z

← Older revision		Revision as of 20:01, 8 February 2014
Line 29:		Line 29:
	</td></tr>		</td></tr>
	</table>		</table>

			==Stereo ==

			{{:T1 ToneMatch® Audio Engine / Stereo Output to Two L1®s}}
	----		----
	[[Category:T1]]		[[Category:T1]]

ST at 17:27, 17 March 2013

2013-03-17T17:27:16Z

← Older revision		Revision as of 17:27, 17 March 2013
Line 7:		Line 7:
	</pre>		</pre>
	</noinclude>		</noinclude>
			{{T1 icon}}{{Model 1S icon}}{{Model II icon}}
	<big>		<big>
	Please note: Bose recommends that if you have two {{{Model\|Model 1S}}} systems using the same source, that you place the {{{Model\|Model 1S}}} systems at least 20 feet apart (6 meters). This is to avoid [[Multiple_Source_Interference\|Multiple Source Interference]]		Please note: Bose recommends that if you have two {{{Model\|Model 1S}}} systems using the same source, that you place the {{{Model\|Model 1S}}} systems at least 20 feet apart (6 meters). This is to avoid [[Multiple_Source_Interference\|Multiple Source Interference]]

ST at 17:25, 17 March 2013

2013-03-17T17:25:04Z

← Older revision		Revision as of 17:25, 17 March 2013
Line 2:		Line 2:
	Usage:		Usage:
	<pre>		<pre>
	{{~~Two T1®s with~~ Two L1®s		{{T1 ToneMatch® Audio Engine to Two L1®s
	\|Model=Model II		\|Model=Model II
	}}		}}

ST: New page: Usage:

 {{Two T1®s with Two L1®s |Model=Model II }}

Please note: Bose recommends that if you have two {{{Model|Model 1S}}} systems using the ...

2013-03-17T17:24:13Z

New page: <noinclude> Usage: <pre> {{Two T1®s with Two L1®s |Model=Model II }} </pre> </noinclude> <big> Please note: Bose recommends that if you have two {{{Model|Model 1S}}} systems using the ...

New page

<noinclude>
Usage:
<pre>
{{Two T1®s with Two L1®s
|Model=Model II
}}
</pre>
</noinclude>
<big>
Please note: Bose recommends that if you have two {{{Model|Model 1S}}} systems using the same source, that you place the {{{Model|Model 1S}}} systems at least 20 feet apart (6 meters). This is to avoid [[Multiple_Source_Interference|Multiple Source Interference]]
</big>

Running two {{{Model|Model 1S}}} systems with the same source is running [[Dual Mono]] and not recommended unless the L1®s are at least 20 feet apart.

[[Image:T1TwoModelII.png]]
<table width=1000><tr>
<td width=400 valign=top>
;System 1
Connect the first system with the ToneMatch cable that came with the T1®.
* T1® ToneMatch port to the {{{Model|Model 1S}}} Power Stand ToneMatch port.
</td>
<td style="width:400px;vertical-align:top">
;System 2
Connect the second system with a ¼ inch jack Tip-Ring-Sleeve cable
* T1® Master Output to the {{{Model|Model 1S}}} Power Stand Analog input
** on the {{{Model|Model 1S}}} Power Stand set the analog input trim to "3" and adjust as necessary to get a good balance with the other system.
** For best results use a Tip-Ring-Sleeve (balanced) connection. <br />[[Image:TrsMtrsM.png]]<br />You can use a Tip-Sleeve (unbalanced connection) but the Tip-Ring-Sleeve (balanced connection is preferred).
</td></tr>
</table>
----
[[Category:T1]]
[[Category:Model 1S]]
[[Category:Model II]]

[[Category:Connections]]