Template:Sub2 with Sub1 - Revision history

ST at 17:46, 2 February 2025

2025-02-02T17:46:43Z

← Older revision		Revision as of 17:46, 2 February 2025
Line 14:		Line 14:

	; Option 2: Crossover frequencies: <br>Sub2: 100—37 Hz <br>Sub1: 200—100 Hz		; Option 2: Crossover frequencies: <br>Sub2: 100—37 Hz <br>Sub1: 200—100 Hz
	# Connect the L1 Pro32 to the Sub2 (~~use~~ the supplied ~~SubMatch~~ cable)		# Connect the L1 Pro32 Line Out to the Sub2 (with an XLR cable and power the Sub2 with the supplied IEC power cable).
	# On the Sub2 set the ~~Line Out~~ EQ to HPF (High Pass Filter)		# On the Sub2 set the LINE IN EQ to LPF [Low Pass Filter] (this sets the crossover to 100 Hz)
	# Connect the Sub2 ~~Line Out~~ to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.		# On the Sub2 set the LINE OUT EQ to HPF [High Pass Filter] (this sets the Line Out to send 100 Hz and higher)
			# Connect the Sub2 LINE OUT to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
	# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs		# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
	# Polarity: Plus on both		# Polarity: Plus on both

ST at 07:10, 2 November 2024

2024-11-02T07:10:55Z

← Older revision		Revision as of 07:10, 2 November 2024
Line 1:		Line 1:
	You can use a Sub1 and Sub2 together. The connection will be L1 Pro32 to Sub2 to Sub1		You can use a Sub1 and Sub2 together. The connection will be L1 Pro32 to Sub2 to Sub1

	There are two options. Either is fine. Choose the one you prefer.		You can stack them or place them side by side. In any arrangement where the grilles fit completely within a 30-inch (75 cm) diameter sphere, your two Subs will act like a single one, only louder. Note: Placing the Subs on either side of the L1 Pro32 power stand does not meet this criteria.

			There are two options. Either is fine. Choose the one you prefer.

	;Option 1: Same crossover frequency applied to both Sub1 and Sub2 (200—37Hz)		;Option 1: Same crossover frequency applied to both Sub1 and Sub2 (200—37Hz)

ST at 07:03, 2 November 2024

2024-11-02T07:03:22Z

← Older revision		Revision as of 07:03, 2 November 2024
Line 12:		Line 12:

	; Option 2: Crossover frequencies: <br>Sub2: 100—37 Hz <br>Sub1: 200—100 Hz		; Option 2: Crossover frequencies: <br>Sub2: 100—37 Hz <br>Sub1: 200—100 Hz
	# Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)		# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)
	# On the Sub2 set the Line Out EQ to HPF (High Pass Filter)		# On the Sub2 set the Line Out EQ to HPF (High Pass Filter)
	# Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.		# Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.

ST at 07:02, 2 November 2024

2024-11-02T07:02:45Z

← Older revision		Revision as of 07:02, 2 November 2024
Line 3:		Line 3:
	There are two options. Either is fine. Choose the one you prefer.		There are two options. Either is fine. Choose the one you prefer.

	;Option 1: Same EQ to both Sub1 and Sub2 (~~37 Hz to~~ 200 Hz)		;Option 1: Same crossover frequency applied to both Sub1 and Sub2 (200—37Hz)
	# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)		# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)
	# Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR		# Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR
Line 11:		Line 11:
	# Polarity: Plus on both		# Polarity: Plus on both

	; Option 2: ~~37 Hz to 100 Hz to~~ Sub2, 100 Hz to 200 Hz ~~to Sub1~~		; Option 2: Crossover frequencies: <br>Sub2: 100—37 Hz <br>Sub1: 200—100 Hz
	# Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)		# Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)
	# On the Sub2 set the Line Out EQ to HPF (High Pass Filter)		# On the Sub2 set the Line Out EQ to HPF (High Pass Filter)

ST at 06:58, 2 November 2024

2024-11-02T06:58:21Z

ST at 06:57, 2 November 2024

2024-11-02T06:57:17Z

@@ Line 1: / Line 1: @@
 You can use a Sub1 and Sub2 together. The connection will be L1 Pro32 to Sub2 to Sub1
 * Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)
 * On the Sub2 set the Line Out EQ to HPF (High Pass Filter)

ST at 06:49, 2 November 2024

2024-11-02T06:49:30Z

← Older revision		Revision as of 06:49, 2 November 2024
Line 2:		Line 2:
	* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)		* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)
	* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)		* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)
	* Connect the Sub2 Line Out to the Sub1 ~~(<html>Correction <strike>optional: use a SubMatch~~ cable to the Sub1~~)</strike></html>~~		* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
	* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs		* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
	* Polarity: Plus on both		* Polarity: Plus on both

ST at 21:02, 2 December 2023

2023-12-02T21:02:40Z

← Older revision		Revision as of 21:02, 2 December 2023
Line 5:		Line 5:
	* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs		* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
	* Polarity: Plus on both		* Polarity: Plus on both
	>!--		<!--
	For more information start at 1:23 in the video below.<br>		For more information start at 1:23 in the video below.<br>
	<html>		<html>

ST at 21:02, 2 December 2023

2023-12-02T21:02:23Z

← Older revision		Revision as of 21:02, 2 December 2023
Line 5:		Line 5:
	* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs		* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
	* Polarity: Plus on both		* Polarity: Plus on both
			>!--
	For more information start at 1:23 in the video below.<br>		For more information start at 1:23 in the video below.<br>
	<html>		<html>
	<iframe width="560" height="315" src="https://www.youtube.com/embed/kQ4Pon0DLcs" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>		<iframe width="560" height="315" src="https://www.youtube.com/embed/kQ4Pon0DLcs" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe></html>
			-->
	----		----
	[[Category:Sub]]		[[Category:Sub]]
	[[Category:Connections]]		[[Category:Connections]]

ST at 06:11, 3 November 2021

2021-11-03T06:11:37Z

← Older revision		Revision as of 06:11, 3 November 2021
Line 2:		Line 2:
	* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)		* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)
	* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)		* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)
	* Connect the Sub2 Line Out to the Sub1 (optional: use a SubMatch cable to the Sub1)		* Connect the Sub2 Line Out to the Sub1 (<html>Correction <strike>optional: use a SubMatch cable to the Sub1)</strike></html>
	* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs		* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
	* Polarity: Plus on both		* Polarity: Plus on both

← Older revision		Revision as of 06:58, 2 November 2024
Line 4:		Line 4:

	;Option 1: Same EQ to both Sub1 and Sub2 (37 Hz to 200 Hz)		;Option 1: Same EQ to both Sub1 and Sub2 (37 Hz to 200 Hz)
	* Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)		# Connect the L1 Pro32 to the Sub2 (use the supplied SubMatch cable)
	* Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR		# Connect the Sub2 to the Sub1 use a SubMatch cable (purchased separately) OR
	** Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.		#* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
	** On the Sub2 set the Line Out EQ to Full (Full Range)		#* On the Sub2 set the Line Out EQ to Full (Full Range)
	* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs		# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
	* Polarity: Plus on both		# Polarity: Plus on both

	; Option 2: 37 Hz to 100 Hz to Sub2, 100 Hz to 200 Hz to Sub1		; Option 2: 37 Hz to 100 Hz to Sub2, 100 Hz to 200 Hz to Sub1
	* Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)		# Connect the L1 Pro32 to the Sub2 (use the SubMatch cable)
	* On the Sub2 set the Line Out EQ to HPF (High Pass Filter)		# On the Sub2 set the Line Out EQ to HPF (High Pass Filter)
	* Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.		# Connect the Sub2 Line Out to the Sub1 with an XLR cable and power the Sub1 with the supplied IEC power cable.
	* Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs		# Level - set to 12:00 o'clock on both. If adjustments are necessary - keep the Level Control the same on both Subs
	* Polarity: Plus on both		# Polarity: Plus on both
	<!--		<!--
	For more information start at 1:23 in the video below.<br>		For more information start at 1:23 in the video below.<br>