T4S to L1 Pro and L1 Legacy - Revision history

ST at 01:37, 4 September 2021

2021-09-04T01:37:12Z

← Older revision		Revision as of 01:37, 4 September 2021
Line 17:		Line 17:

	* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro		* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro
			* On the L1 Pro, turn down the volume and/or mute any unused channels
	* Use a 1/4 (6.3 mm) TRS cable to connect the T4S Left (analog) output to the [[Model II]] or [[Model 1S]] analog input		* Use a 1/4 (6.3 mm) TRS cable to connect the T4S Left (analog) output to the [[Model II]] or [[Model 1S]] analog input
	* Set the Input trim on the [[Model II]] or [[Model 1S]] to 10:00 o'clock		* Set the Input trim on the [[Model II]] or [[Model 1S]] to 10:00 o'clock
Line 31:		Line 32:

	* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro		* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro
			* On the L1 Pro, turn down the volume and/or mute any unused channels
	* Use another [[ToneMatch Cable\|ToneMatch cable (or equivalent)]] to connect to the [[Model II]] or [[Model 1S]] ToneMatch port<br>'''Note''': The trim control has no effect on the signal at the ToneMatch port. Leave the trim control off (fully counterclockwise) unless you have something connected to the analog line in		* Use another [[ToneMatch Cable\|ToneMatch cable (or equivalent)]] to connect to the [[Model II]] or [[Model 1S]] ToneMatch port<br>'''Note''': The trim control has no effect on the signal at the ToneMatch port. Leave the trim control off (fully counterclockwise) unless you have something connected to the analog line in
	* Adjust the relative levels using the T4S channel pan and controls		* Adjust the relative levels using the T4S channel pan and controls

ST at 15:47, 12 June 2021

2021-06-12T15:47:27Z

← Older revision		Revision as of 15:47, 12 June 2021
Line 31:		Line 31:

	* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro		* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro
	* Use another [[ToneMatch Cable\|ToneMatch cable (or equivalent)]] to connect to the [[Model II]] or [[Model 1S]] ToneMatch port<br>;Note: The trim control has no effect on the signal at the ToneMatch port		* Use another [[ToneMatch Cable\|ToneMatch cable (or equivalent)]] to connect to the [[Model II]] or [[Model 1S]] ToneMatch port<br>'''Note''': The trim control has no effect on the signal at the ToneMatch port. Leave the trim control off (fully counterclockwise) unless you have something connected to the analog line in
	* Adjust the relative levels using the T4S channel pan and controls		* Adjust the relative levels using the T4S channel pan and controls

ST at 11:21, 12 June 2021

2021-06-12T11:21:43Z

← Older revision		Revision as of 11:21, 12 June 2021
Line 22:		Line 22:

	[[File:T4S to L1 Pro and L1 Legacy Digital Analog.jpg]]		[[File:T4S to L1 Pro and L1 Legacy Digital Analog.jpg]]

			=== Analog Connection (Green) ===
			{{1/4 TRS Balanced}}


	== Two Digital Connections ==		== Two Digital Connections ==

ST at 03:27, 12 June 2021

2021-06-12T03:27:08Z

← Older revision		Revision as of 03:27, 12 June 2021
Line 3:		Line 3:
	\|RightBody = To connect the T4S to an L1 Pro (any model) and a [[Model II]] or [[Model 1S]] there are a couple of approaches.		\|RightBody = To connect the T4S to an L1 Pro (any model) and a [[Model II]] or [[Model 1S]] there are a couple of approaches.

	The T4S has two ToneMatch Ports. If you use a T4S to control two identical L1 systems, then you can use both ToneMatch ports. However, if you have an L1 Pro (any model) and a [[Model II]] or [[Model 1S]] you may want to use the right ToneMatch port to the L1 Pro and the Analog Left Output to the [[Model II]] or [[Model 1S]]		The T4S has two ToneMatch Ports. If you use a T4S to control two identical L1 systems, then you can use both ToneMatch ports. However, if you have an L1 Pro (any model) and a [[Model II]] or [[Model 1S]] you may want to use the right ToneMatch port to the L1 Pro and the Analog Left Output to the [[Model II]] or [[Model 1S]]. See below for details about why you would choose one approach over the other.

	\|Categories =		\|Categories =
Line 14:		Line 14:

	== Digital and Analog Connection ==		== Digital and Analog Connection ==
	Use this method if you are running stereo or ~~dual mono~~ and you need to adjust or balance the volumes of the two L1 systems.		Use this method if you are running stereo or [[Dual Mono]] and you need to adjust or balance the volumes of the two L1 systems.

	* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro		* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro
Line 24:		Line 24:

	== Two Digital Connections ==		== Two Digital Connections ==
	Use this method if you don't need to control the relative volumes of the two L1 systems. For example: If you are sending two inputs to the L1 Pro, and two inputs to the [[Model II]] or [[Model 1S]]. Then you will use the T4S channel PAN and volume controls to manage the mix.		Use this method if you don't need to control the relative volumes of the two L1 systems. This would be typical of a [[Multi Mono]] setup. For example: If you are sending two inputs to the L1 Pro, and two inputs to the [[Model II]] or [[Model 1S]]. Then you will use the T4S channel PAN and volume controls to manage the mix.

	* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro		* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro

ST at 03:22, 12 June 2021

2021-06-12T03:22:36Z

← Older revision	Revision as of 03:22, 12 June 2021
(No difference)

ST at 03:22, 12 June 2021

2021-06-12T03:22:36Z

← Older revision		Revision as of 03:22, 12 June 2021
Line 13:		Line 13:
	}}		}}

	=== Digital and Analog Connection ===		== Digital and Analog Connection ==
	Use this method if you are running stereo or dual mono and you need to adjust or balance the volumes of the two L1 systems.		Use this method if you are running stereo or dual mono and you need to adjust or balance the volumes of the two L1 systems.

Line 23:		Line 23:
	[[File:T4S to L1 Pro and L1 Legacy Digital Analog.jpg]]		[[File:T4S to L1 Pro and L1 Legacy Digital Analog.jpg]]

	=== Two Digital Connections ===		== Two Digital Connections ==
	Use this method if you don't need to control the relative volumes of the two L1 systems. For example: If you are sending two inputs to the L1 Pro, and two inputs to the [[Model II]] or [[Model 1S]]. Then you will use the T4S channel PAN and volume controls to manage the mix.		Use this method if you don't need to control the relative volumes of the two L1 systems. For example: If you are sending two inputs to the L1 Pro, and two inputs to the [[Model II]] or [[Model 1S]]. Then you will use the T4S channel PAN and volume controls to manage the mix.

Line 32:		Line 32:
	[[File:T4S to L1 Pro and L1 Legacy Digital.jpg]]		[[File:T4S to L1 Pro and L1 Legacy Digital.jpg]]

			== ToneMatch Cable==
			{{ToneMatch Cable}}

ST at 03:21, 12 June 2021

2021-06-12T03:21:33Z

← Older revision		Revision as of 03:21, 12 June 2021
Line 27:		Line 27:

	* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro		* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro
	* Use another ToneMatch cable (or equivalent) to connect to the [[Model II]] or [[Model 1S]] ToneMatch port<br>;Note: The trim control has no effect on the signal at the ToneMatch port		* Use another [[ToneMatch Cable\|ToneMatch cable (or equivalent)]] to connect to the [[Model II]] or [[Model 1S]] ToneMatch port<br>;Note: The trim control has no effect on the signal at the ToneMatch port
	* Adjust the relative levels using the T4S channel pan and controls		* Adjust the relative levels using the T4S channel pan and controls

ST at 02:53, 12 June 2021

2021-06-12T02:53:58Z

← Older revision		Revision as of 02:53, 12 June 2021
Line 1:		Line 1:
	{{DivToc		{{DivToc
	\|RightHead = Introduction		\|RightHead = Introduction
	\|RightBody = The T4S has two ToneMatch Ports. If you use a T4S to control two identical L1 systems, then you can use ~~the~~ ToneMatch ports. However, if you have an L1 Pro (any model) and an [[Model II]] or [[Model 1S]] you may want to use the right ToneMatch port to the L1 Pro and the Analog Left Output to the [[Model II]] or [[Model 1S]]		\|RightBody = To connect the T4S to an L1 Pro (any model) and a [[Model II]] or [[Model 1S]] there are a couple of approaches.

			The T4S has two ToneMatch Ports. If you use a T4S to control two identical L1 systems, then you can use both ToneMatch ports. However, if you have an L1 Pro (any model) and a [[Model II]] or [[Model 1S]] you may want to use the right ToneMatch port to the L1 Pro and the Analog Left Output to the [[Model II]] or [[Model 1S]]

	\|Categories =		\|Categories =
Line 10:		Line 12:
	[[Category:Connections]]		[[Category:Connections]]
	}}		}}
	~~To connect the T4S to an L1 Pro (any model) and an [[Model II]] or [[Model 1S]]~~

	=== Digital and Analog Connection ===		=== Digital and Analog Connection ===

ST at 02:51, 12 June 2021

2021-06-12T02:51:54Z

← Older revision		Revision as of 02:51, 12 June 2021
Line 1:		Line 1:
	To connect the T4S to an L1 Pro (any model) and a [[Model II]] or [[Model 1S]]		{{DivToc
			\|RightHead = Introduction
			\|RightBody = The T4S has two ToneMatch Ports. If you use a T4S to control two identical L1 systems, then you can use the ToneMatch ports. However, if you have an L1 Pro (any model) and an [[Model II]] or [[Model 1S]] you may want to use the right ToneMatch port to the L1 Pro and the Analog Left Output to the [[Model II]] or [[Model 1S]]

			\|Categories =
			[[Category:L1 Pro]]
			[[Category:T4S]]
			[[Category:Model II]]
			[[Category:Model 1S]]
			[[Category:Connections]]
			}}
			To connect the T4S to an L1 Pro (any model) and an [[Model II]] or [[Model 1S]]

	=== Digital and Analog Connection ===		=== Digital and Analog Connection ===

ST: /* Two Digital Connections */

2021-06-12T02:46:44Z

Two Digital Connections

← Older revision		Revision as of 02:46, 12 June 2021
Line 15:		Line 15:

	* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro		* Use the ToneMatch cable (included with the T4S) to connect the Right digital output to the L1 Pro ToneMatch port. Power will be supplied by the L1 Pro
	* Use another ToneMatch cable (or equivalent) to connect to the [[Model II]] or [[Model 1S]] ToneMatch port		* Use another ToneMatch cable (or equivalent) to connect to the [[Model II]] or [[Model 1S]] ToneMatch port<br>;Note: The trim control has no effect on the signal at the ToneMatch port
	* Adjust the relative levels using the T4S channel pan controls		* Adjust the relative levels using the T4S channel pan and controls

	[[File:T4S to L1 Pro and L1 Legacy Digital.jpg]]		[[File:T4S to L1 Pro and L1 Legacy Digital.jpg]]