ST: Replaced content with "{{T4S/T8S Mono Output}} ---- Category:T4S Category:T8S Category:Mono "

2019-11-06T16:04:07Z

Replaced content with "{{T4S/T8S Mono Output}} <noinclude> ---- Category:T4S Category:T8S Category:Mono </noinclude>"

← Older revision		Revision as of 16:04, 6 November 2019
Line 1:		Line 1:
	{{~~== Mono Output ==~~		{{T4S/T8S Mono Output}}
	~~On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO).~~
	;Please note: There is no hardwired summed mono output on the ToneMatch mixers. Any input signal that is panned hard Left will not be heard through the Right output. To get a mono output please see below.

	~~=== General Information ===~~
	As you move the pan control away from the center, the sound level increases slightly in one direction and decreases in the other. If you pan inputs hard to one side (e.g., Right) and the Right output will be slightly louder (theoretically, up to +3 dB louder) than if you had panned the inputs up the middle. And panned hard Right - there will be no signal at the Left Output.

	~~===~~T4S ~~ToneMatch® mixer===~~

	*Pan all inputs hard RIGHT
	*Connect your L1® to the RIGHT ToneMatch® port

	OR

	*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable.

	~~;Note: Anything panned hard LEFT will not be heard at the RIGHT Output.~~

	~~===~~T8S ~~ToneMatch® mixer===~~

	*Pan all inputs hard RIGHT
	*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable

	OR

	*Use the XLR Right Output to powered a loudspeaker (e.g. S1 Pro, F1 Model 812). or L1® Compact with XLR to ¼ inch (6mm) jack Tip-Ring-Sleeve.

	~~;Note: Anything panned hard LEFT will not be heard at the RIGHT Output.~~

	~~===~~ Mono ~~using Aux Output ===~~
	~~You can create a summed mono output by directing your input channels (1-4 or 1-8) to an Aux~~ Output~~. See [[{{PAGENAME}}#Aux Outputs\|Aux Outputs]] for details.~~}}

	<noinclude>		<noinclude>

ST: Created page with "{{== Mono Output == On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO). ;Please note: There is no hardwired summed mono output on the T..."

2019-11-06T16:03:28Z

Created page with "{{== Mono Output == On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO). ;Please note: There is no hardwired summed mono output on the T..."

New page

{{== Mono Output ==
On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO).
;Please note: There is no hardwired summed mono output on the ToneMatch mixers. Any input signal that is panned hard Left will not be heard through the Right output. To get a mono output please see below.

=== General Information ===
As you move the pan control away from the center, the sound level increases slightly in one direction and decreases in the other. If you pan inputs hard to one side (e.g., Right) and the Right output will be slightly louder (theoretically, up to +3 dB louder) than if you had panned the inputs up the middle. And panned hard Right - there will be no signal at the Left Output.

===T4S ToneMatch® mixer===

*Pan all inputs hard RIGHT
*Connect your L1® to the RIGHT ToneMatch® port

OR

*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable.

;Note: Anything panned hard LEFT will not be heard at the RIGHT Output.

===T8S ToneMatch® mixer===

*Pan all inputs hard RIGHT
*Use the ¼ inch (6mm) Right Output to a powered loudspeaker (e.g. S1 Pro, L1® Compact, F1 Model 812). For best results use a ¼ inch (6mm) jack Tip-Ring-Sleeve cable

OR

*Use the XLR Right Output to powered a loudspeaker (e.g. S1 Pro, F1 Model 812). or L1® Compact with XLR to ¼ inch (6mm) jack Tip-Ring-Sleeve.

;Note: Anything panned hard LEFT will not be heard at the RIGHT Output.

=== Mono using Aux Output ===
You can create a summed mono output by directing your input channels (1-4 or 1-8) to an Aux Output. See [[{{PAGENAME}}#Aux Outputs|Aux Outputs]] for details.}}

<noinclude>
----
[[Category:T4S]]
[[Category:T8S]]
[[Category:Mono]]
</noinclude>

T4S/T8S Mono Output - Revision history

ST: Replaced content with "{{T4S/T8S Mono Output}} ---- Category:T4S Category:T8S Category:Mono "

ST: Created page with "{{== Mono Output == On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO). ;Please note: There is no hardwired summed mono output on the T..."