T1 ToneMatch® Audio Engine to F1 System - Revision history

ST: /* Mono Connection */

2019-10-29T17:37:06Z

Mono Connection

← Older revision		Revision as of 17:37, 29 October 2019
Line 28:		Line 28:


	To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input.		To connect a {{T1}} to an {{F1}} you will run a cable from the T1® Master Output to the {{F1}} Channel 1 or Channel 2 1/4 input. Use a ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve cable.
			[[Image:TrsMtrsM.png\|600px]]

	[[Image:T1 to F1 Model 812 Mono.png\|600px]]		[[Image:T1 to F1 Model 812 Mono.png\|600px]]
Line 37:		Line 38:
	'''For best results use a balanced connection		'''For best results use a balanced connection

	; ¼ Inch Tip-Ring-Sleeve ~~(balanced)~~ to ¼ Inch Tip-Ring-Sleeve ~~(balanced)~~'''		; ¼ Inch Tip-Ring-Sleeve to ¼ Inch Tip-Ring-Sleeve'''

	A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.		A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.
Line 47:		Line 48:
	=== XLR connection from F1 Model 812 Line Out to second F1 Model 812 Channel 1 ===		=== XLR connection from F1 Model 812 Line Out to second F1 Model 812 Channel 1 ===
	Use an ordinary microphone cable to connect the first F1 Model 812 to the second one.		Use an ordinary microphone cable to connect the first F1 Model 812 to the second one.

			=== General settings ===
			* Turn the volume off for any channels you are not using. In the diagram above, you would turn off channel 2 for both F1 systems.
			* On the first F1, set the Level Control to MIC
			* On the second F1, set the Level Control to LINE
			* Set the volume on the second F1 to 10:00 o'clock. Then adjust the volume on the second F1 to match the output of the first F1 (if necessary). It's likely, you will have the volume on the second F1 lower than the first. That is normal.
			** Note: The volume control on the first F1 will raise and lower the volume on the second F1


	=== Using an F1 Subwoofer ===		=== Using an F1 Subwoofer ===

ST at 15:31, 9 July 2019

2019-07-09T15:31:09Z

← Older revision		Revision as of 15:31, 9 July 2019
Line 15:		Line 15:
	=== {{T1 nl}} to F1 Model 812 (not F1 Subwoofer) ===		=== {{T1 nl}} to F1 Model 812 (not F1 Subwoofer) ===
	{{F1 icon}}{{t1 icon}}		{{F1 icon}}{{t1 icon}}
	If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the {{t1}} to the F1 Model 812 instead of the F1 Subwoofer.		If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the {{t1}} to the F1 Model 812 instead of the F1 Subwoofer. Then connect the F1 Model 812 LINE OUT to the F1 Subwoofer.

	=== {{T1 nl}} with {{l1}} as stage monitor with F1 Model 812 as Front of House ===		=== {{T1 nl}} with {{l1}} as stage monitor with F1 Model 812 as Front of House ===

ST: /* Master / Monitor */

2017-05-13T15:21:20Z

Master / Monitor

← Older revision		Revision as of 15:21, 13 May 2017
Line 54:		Line 54:

	== Master / Monitor ==		== Master / Monitor ==
			=== No L1® Model II or Model 1S for Monitor ===
			Consider running a {{Compact}} for your monitor.

	If you ~~aren't using an L1® Model II or L1®~~ Model ~~1S as a stage monitor, you~~ can take a line from the end of the F1 signal chain to a {{Compact}} or third party monitor.		Your signal path would be T1® Master Output to Compact to F1 Model 812. Note: When you change the volume on the {{Compact}} it will affect the volume to the F1 Model 812

			-=OR=-

			You can take a line from the end of the F1 signal chain to a {{Compact}} or third party monitor. This will allow you to change the volume on the {{Compact}} or monitor without affecting the volume on the F1 Model 812.

	[[File:T1 F1 Model 812 F1 Subwoofer Compact or Monitor.png]]		[[File:T1 F1 Model 812 F1 Subwoofer Compact or Monitor.png]]

ST: /* Master / Monitor */

2017-05-13T15:10:45Z

Master / Monitor

← Older revision		Revision as of 15:10, 13 May 2017
Line 54:		Line 54:

	== Master / Monitor ==		== Master / Monitor ==
	If you aren't using an L1® as a stage monitor, you can use the T1 Aux output to run a separate signal to your monitor.
			If you aren't using an L1® Model II or L1® Model 1S as a stage monitor, you can take a line from the end of the F1 signal chain to a {{Compact}} or third party monitor.

			[[File:T1 F1 Model 812 F1 Subwoofer Compact or Monitor.png]]



			=== T1® Aux to Monitor ===

			You can use the T1 Aux output to run a separate signal to your monitor.
	See [[T1 ToneMatch® Audio Engine / Aux]] for details.		See [[T1 ToneMatch® Audio Engine / Aux]] for details.

ST: /* Master / Monitor or Stereo Connection */

2017-05-13T15:01:49Z

Master / Monitor or Stereo Connection

← Older revision		Revision as of 15:01, 13 May 2017
Line 53:		Line 53:
	[[Image:T1 to F1 Model 812 with F1 Subwoofer.png]]		[[Image:T1 to F1 Model 812 with F1 Subwoofer.png]]

	== Master / Monitor ~~or Stereo Connection~~ ==		== Master / Monitor ==
	If you aren't using an L1® as a stage monitor, you can use the T1 Aux output to run a separate signal to your monitor.		If you aren't using an L1® as a stage monitor, you can use the T1 Aux output to run a separate signal to your monitor.
	See [[T1 ToneMatch® Audio Engine / Aux]] for details.		See [[T1 ToneMatch® Audio Engine / Aux]] for details.

			The {{Compact}} can be used for a monitor.

	[[File:T1 F1 Model 812 Compact or Monitor.png]]		[[File:T1 F1 Model 812 Compact or Monitor.png]]

ST: /* Master / Monitor or Stereo Connection */

2017-05-13T14:59:00Z

Master / Monitor or Stereo Connection

← Older revision		Revision as of 14:59, 13 May 2017
Line 56:		Line 56:
	If you aren't using an L1® as a stage monitor, you can use the T1 Aux output to run a separate signal to your monitor.		If you aren't using an L1® as a stage monitor, you can use the T1 Aux output to run a separate signal to your monitor.
	See [[T1 ToneMatch® Audio Engine / Aux]] for details.		See [[T1 ToneMatch® Audio Engine / Aux]] for details.

			[[File:T1 F1 Model 812 Compact or Monitor.png]]

	== Stereo Connection ==		== Stereo Connection ==

ST: /* Stereo Connection */

2017-05-13T14:36:06Z

Stereo Connection

← Older revision		Revision as of 14:36, 13 May 2017
Line 52:		Line 52:

	[[Image:T1 to F1 Model 812 with F1 Subwoofer.png]]		[[Image:T1 to F1 Model 812 with F1 Subwoofer.png]]

			== Master / Monitor or Stereo Connection ==
			If you aren't using an L1® as a stage monitor, you can use the T1 Aux output to run a separate signal to your monitor.
			See [[T1 ToneMatch® Audio Engine / Aux]] for details.

	== Stereo Connection ==		== Stereo Connection ==
	If you have split a stereo signal to T1® Master and T1® Aux see a detailed article [[T1 ToneMatch® Audio Engine / Stereo Output to Two F1 Systems]].		If you have to split a stereo signal to T1® Master and T1® Aux see a detailed article [[T1 ToneMatch® Audio Engine / Stereo Output to Two F1 Systems]].

	Here is a quick overview.		Here is a quick overview.

ST: /* XLR connection from F1 Model 812 Line Out to second F1 Channel 1 */

2017-05-13T14:30:49Z

XLR connection from F1 Model 812 Line Out to second F1 Channel 1

← Older revision		Revision as of 14:30, 13 May 2017
Line 45:		Line 45:
	The output from the T1® is balanced mono, as are the XLR and ¼ inch inputs on the F1 System. Use a ¼ inch jack Tip-Ring-Sleeve cable to make a balanced connection. If you use a ¼ inch jack Tip-Sleeve cable you will be making an unbalanced connection (-6dB less gain than a balanced connection).		The output from the T1® is balanced mono, as are the XLR and ¼ inch inputs on the F1 System. Use a ¼ inch jack Tip-Ring-Sleeve cable to make a balanced connection. If you use a ¼ inch jack Tip-Sleeve cable you will be making an unbalanced connection (-6dB less gain than a balanced connection).

	=== XLR connection from F1 Model 812 Line Out to second F1 Channel 1 ===		=== XLR connection from F1 Model 812 Line Out to second F1 Model 812 Channel 1 ===
	Use an ordinary microphone cable to connect the first F1 Model 812 to the second one.		Use an ordinary microphone cable to connect the first F1 Model 812 to the second one.

	=== Using an F1 Subwoofer ===		=== Using an F1 Subwoofer ===

ST: /* {{T1}} Considerations */

2017-05-13T14:29:19Z

{{T1}} Considerations

← Older revision		Revision as of 14:29, 13 May 2017
Line 12:		Line 12:
	</td>		</td>
	</tr></table>		</tr></table>
	== {{T1}} Considerations ==		== {{T1 nl}} Considerations ==
	=== {{T1}} to F1 Model 812 (not F1 Subwoofer) ===		=== {{T1 nl}} to F1 Model 812 (not F1 Subwoofer) ===
			{{F1 icon}}{{t1 icon}}
			If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the {{t1}} to the F1 Model 812 instead of the F1 Subwoofer.

	~~If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the T1® to the F1 Model 812 instead of the F1 Subwoofer.~~		=== {{T1 nl}} with {{l1}} as stage monitor with F1 Model 812 as Front of House ===
			{{F1 icon}}{{Model II icon}} {{t1 icon}}
	=== {{T1}} with {{l1}} as stage monitor with F1 Model 812 as Front of House ===
	Connecting the T1® to the F1 Model 812 Channel 1, you can control the relative loudness of the F1 Stack (F1 Model 812 with F1 Subwoofer) to your {{L1}} with the F1 Model 812 Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1. You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.		Connecting the T1® to the F1 Model 812 Channel 1, you can control the relative loudness of the F1 Stack (F1 Model 812 with F1 Subwoofer) to your {{L1}} with the F1 Model 812 Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1. You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.

	=== ~~T1®~~ Master Volume ===		=== {{t1 nl}} Master Volume ===
	If you want to run the T1® full output without it being affected by the T1® Master Volume see [[T1® Audio Engine / Master Output Pre / Post]]		If you want to run the T1® full output without it being affected by the T1® Master Volume see [[T1® Audio Engine / Master Output Pre / Post]]

ST: /* {{T1}} Considerations */

2017-05-13T14:25:09Z

{{T1}} Considerations

← Older revision		Revision as of 14:25, 13 May 2017
Line 13:		Line 13:
	</tr></table>		</tr></table>
	== {{T1}} Considerations ==		== {{T1}} Considerations ==
			=== {{T1}} to F1 Model 812 (not F1 Subwoofer) ===

	If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the T1® to the F1 Model 812 instead of the F1 Subwoofer.		If you have an F1 Subwoofer you will have more flexibility with the sound output if you connect the T1® to the F1 Model 812 instead of the F1 Subwoofer.

	Connecting the T1® to the F1 Model 812 Channel 1, you can control the relative loudness of the F1 Stack (F1 Model 812 with F1 Subwoofer) to your ~~L1®~~ with the Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1. You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.		=== {{T1}} with {{l1}} as stage monitor with F1 Model 812 as Front of House ===
			Connecting the T1® to the F1 Model 812 Channel 1, you can control the relative loudness of the F1 Stack (F1 Model 812 with F1 Subwoofer) to your {{L1}} with the F1 Model 812 Channel 1 Volume Control. If you are running the T1® Master at a relatively low volume because you don't need much volume from the L1® you can set the Signal Input switch to MIC instead of Line Level if you need more volume from the F1. You will not harm the system by doing this. You can also turn up the F1 Channel 1 Volume until you are seeing long red flickers (up to 1 second). If you are seeing solid red, then turn the Volume control down.

	=== T1® Master Volume ===		=== T1® Master Volume ===
	If you want to run the T1® full output without it being affected by the T1® Master Volume see [[T1® Audio Engine / Master Output Pre / Post]]		If you want to run the T1® full output without it being affected by the T1® Master Volume see [[T1® Audio Engine / Master Output Pre / Post]]




	== Mono Connection ==		== Mono Connection ==