Sennheiser XSW IEM - Revision history

ST: /* Limiter */

2022-11-14T19:20:48Z

Limiter

← Older revision		Revision as of 19:20, 14 November 2022
Line 12:		Line 12:
	== Limiter ==		== Limiter ==
	:Q The specifications mention a -10 dB limiter. When I engage the limiter - I don't hear any difference. How is the limiter supposed to work?		:Q The specifications mention a -10 dB limiter. When I engage the limiter - I don't hear any difference. How is the limiter supposed to work?
	:A ~~Being investigated~~		:A The development goal was, that you can’t hear it…
			The Limiter is adaptive. It’s limiting to a Maximum output of approx. 450mV @16Ohms at the Headphone Amp. However, it is affected by the individual Impedance of the headphones used and the efficiency of the headphones drivers.

			Interesting to note: The impedance of the IE 4, IE 400 PRO, IE 500 PRO, are all 16 ohms

ST: /* LED on Receiver Body Pack */

2022-11-13T07:43:27Z

LED on Receiver Body Pack

← Older revision		Revision as of 07:43, 13 November 2022
Line 6:		Line 6:

	== LED on Receiver Body Pack ==		== LED on Receiver Body Pack ==
	;Q :Does the LED flickering orange indicate clipping? If so, why doesn't this correspond with the display on the transmitter?		;Q Does the LED flickering orange indicate clipping? If so, why doesn't this correspond with the display on the transmitter?
	;A :The clip indication on the receiver is a little bit earlier, than on the transmitter. ~~therefore~~ you see it already kind of orange on the receiver as it stays “clean” on the transmitter. Especially on such short signals as a click you will notice that. But it’s nothing to worry about.		;A The clip indication on the receiver is a little bit earlier than on the transmitter.
			:Therefore you see it already kind of orange on the receiver as it stays “clean” on the transmitter. Especially on such short signals as a click you will notice that. But it’s nothing to worry about.

	== Limiter ==		== Limiter ==

ST: /* LED in Receiver */

2022-11-13T07:42:22Z

LED in Receiver

← Older revision		Revision as of 07:42, 13 November 2022
Line 5:		Line 5:
	{{:Sennheiser Wireless Antennas}}		{{:Sennheiser Wireless Antennas}}

	== LED in Receiver ==		== LED on Receiver Body Pack ==
	:Q Does the LED flickering orange indicate clipping? If so, why doesn't this correspond with the display on the transmitter?		;Q :Does the LED flickering orange indicate clipping? If so, why doesn't this correspond with the display on the transmitter?
	:A		;A :The clip indication on the receiver is a little bit earlier, than on the transmitter. therefore you see it already kind of orange on the receiver as it stays “clean” on the transmitter. Especially on such short signals as a click you will notice that. But it’s nothing to worry about.
	The clip indication on the receiver is a little bit earlier, than on the transmitter. therefore you see it already kind of orange on the receiver as it stays “clean” on the transmitter. Especially on such short signals as a click you will notice that. But it’s nothing to worry about.

	== Limiter ==		== Limiter ==

ST: Created page with " ==Antenna Questions== {{:Sennheiser Wireless Antennas}} == LED in Receiver == :Q Does the LED flickering orange indicate clipping? If so, why doesn't this correspond with..."

2022-11-13T07:41:32Z

Created page with " ==Antenna Questions== {{:Sennheiser Wireless Antennas}} == LED in Receiver == :Q Does the LED flickering orange indicate clipping? If so, why doesn't this correspond with..."

New page

==Antenna Questions==

{{:Sennheiser Wireless Antennas}}

== LED in Receiver ==
:Q Does the LED flickering orange indicate clipping? If so, why doesn't this correspond with the display on the transmitter?
:A
The clip indication on the receiver is a little bit earlier, than on the transmitter. therefore you see it already kind of orange on the receiver as it stays “clean” on the transmitter. Especially on such short signals as a click you will notice that. But it’s nothing to worry about.

== Limiter ==
:Q The specifications mention a -10 dB limiter. When I engage the limiter - I don't hear any difference. How is the limiter supposed to work?
:A Being investigated

-----
[[Category:Sennheiser]]
[[Category:IEM]]
[[Category:Wireless]]