Mixer to Share Presets on S1 Pro - Revision history

ST: Text replacement - "Category:S1" to "Category:S1 Pro"

2019-11-17T02:23:44Z

Text replacement - "Category:S1" to "Category:S1 Pro"

← Older revision		Revision as of 02:23, 17 November 2019
Line 68:		Line 68:
	[[Category:Connections]]		[[Category:Connections]]
	[[Category:Mixer]]		[[Category:Mixer]]
	[[Category:S1]]		[[Category:S1 Pro]]

ST: corrections

2018-10-18T17:28:38Z

corrections

← Older revision		Revision as of 17:28, 18 October 2018
Line 18:		Line 18:
	For the following discussion, a "side" of the mixer is either Left or Right, or it could be a "buss" or "alt" channel routing.		For the following discussion, a "side" of the mixer is either Left or Right, or it could be a "buss" or "alt" channel routing.
	* Pool all microphone inputs to one side of the mixer (e.g. LEFT).		* Pool all microphone inputs to one side of the mixer (e.g. LEFT).
	** Take the pooled output (LEFT output the mixer) to S1 Pro channel 1 with ToneMatch switch set to Microphone)		** Take the pooled output (LEFT output the mixer) to S1 Pro channel 1 with ToneMatch switch set to Microphone.

	* Pool all other inputs to the other side of the mixer (e.g. RIGHT)		* Pool all other inputs to the other side of the mixer (e.g. RIGHT)

	If these inputs are not acoustic guitars with pickups run the mixer RIGHT output to S1 Pro channel 2 with the ToneMatch switch set to ~~Guitar~~.		If these inputs are not acoustic guitars with pickups run the mixer RIGHT output to S1 Pro channel 2 with the ToneMatch switch set to Off.
	* Take the pooled output (the other side of the mixer) to S1 Pro channel 2 and use a Preset that is appropriate for the input~~, or Preset 00~~.		* Take the pooled output (the other side of the mixer) to S1 Pro channel 2 and use a Preset that is appropriate for the input (Mic Guitar Off).
	** Take the pooled output (RIGHT output on the mixer) to S1 Pro channel 2		** Take the pooled output (RIGHT output on the mixer) to S1 Pro channel 2
	** If the inputs are acoustic guitars with pickups set the ToneMatch switch to Guitar		** If the inputs are acoustic guitars with pickups set the ToneMatch switch to Guitar

ST at 17:17, 18 October 2018

2018-10-18T17:17:50Z

← Older revision		Revision as of 17:17, 18 October 2018
Line 1:		Line 1:
	{{~~S1icon~~}}		{{S1 icon}}
	__NOEDITSECTION__		__NOEDITSECTION__
	<noinclude><table><tr>		<noinclude><table><tr>
Line 7:		Line 7:
	This article is about using a Mixer to allow more than one input per {{S1}} channel to use [[ToneMatch®\|ToneMatch® Presets]].		This article is about using a Mixer to allow more than one input per {{S1}} channel to use [[ToneMatch®\|ToneMatch® Presets]].

	[[File:MixerToSharePresetsS1Pro.jpg\|~~right~~]]		[[File:MixerToSharePresetsS1Pro.jpg\|Mixer to S1 Pro to share Presets]]
	</td>		</td>
	</tr></table> </noinclude>		</tr></table> </noinclude>
Line 30:		Line 30:
	=== Example ===		=== Example ===
	==== 2 Vocals, 2 Guitars ====		==== 2 Vocals, 2 Guitars ====
	* You have two vocal microphones. Route these through the mixer to S1 Pro channel 1		* You have two vocal microphones. Route these through the mixer to S1 Pro channel 1 with ToneMatch switch to Mic.
	* You have two similar Acoustic Guitars with pickups. Route these through the mixer to S1 Pro channel 2 with ToneMatch switch to Guitar.		* You have two similar Acoustic Guitars with pickups. Route these through the mixer to S1 Pro channel 2 with ToneMatch switch to Guitar.

	[[File:MixerToSharePresetsS1Pro.jpg]]		[[File:MixerToSharePresetsS1Pro.jpg]]



	===== Connections =====		===== Connections =====
			[[File:S1 Pro Chan 12 Mic Guitar 600.jpg]]
	====== Microphones ======		====== Microphones ======
	# Run both microphones to the mixer.		# Run both microphones to the mixer.

ST: Created page with "{{S1icon}} NOEDITSECTION
TOC {{ToneMatch icon}} This article is about using a Mixer to allow..."
2018-10-18T17:12:04Z

Created page with "{{S1icon}} NOEDITSECTION <noinclude><table><tr> <td valign="top" width="250">TOC</td> <td valign="top"> {{ToneMatch icon}} This article is about using a Mixer to allow..."

New page
{{S1icon}}
NOEDITSECTION
<noinclude><table><tr>
<td valign="top" width="250">TOC</td>
<td valign="top">
{{ToneMatch icon}}
This article is about using a Mixer to allow more than one input per {{S1}} channel to use [[ToneMatch®|ToneMatch® Presets]].

[[File:MixerToSharePresetsS1Pro.jpg|right]]
</td>
</tr></table> </noinclude>
=== Assumptions ===
* You have more than two inputs requiring Presets.
* Two or more of those inputs are similar, for example: microphones that are of the same make and model.
* You have a stereo mixer or one that has two distinct busses.

=== General Principles ===
For the following discussion, a "side" of the mixer is either Left or Right, or it could be a "buss" or "alt" channel routing.
* Pool all microphone inputs to one side of the mixer (e.g. LEFT).
** Take the pooled output (LEFT output the mixer) to S1 Pro channel 1 with ToneMatch switch set to Microphone)

* Pool all other inputs to the other side of the mixer (e.g. RIGHT)

If these inputs are not acoustic guitars with pickups run the mixer RIGHT output to S1 Pro channel 2 with the ToneMatch switch set to Guitar.
* Take the pooled output (the other side of the mixer) to S1 Pro channel 2 and use a Preset that is appropriate for the input, or Preset 00.
Take the pooled output (RIGHT output on the mixer) to S1 Pro channel 2
If the inputs are acoustic guitars with pickups set the ToneMatch switch to Guitar
** If the inputs are NOT acoustic guitars with pickups set the ToneMatch switch to Off

=== Example ===
==== 2 Vocals, 2 Guitars ====
* You have two vocal microphones. Route these through the mixer to S1 Pro channel 1
* You have two similar Acoustic Guitars with pickups. Route these through the mixer to S1 Pro channel 2 with ToneMatch switch to Guitar.

[[File:MixerToSharePresetsS1Pro.jpg]]

===== Connections =====
====== Microphones ======
# Run both microphones to the mixer.
# On the input strips for the microphones pan all the way to the LEFT
# Run the Mixer LEFT output to the S1 Pro channel 1
# Set the S1 Pro channel 1 ToneMatch Switch to Microphone
====== Guitars ======
# Run both Guitars to the mixer.
# On the input strips for the Guitars pan all the way to the RIGHT
# Run the Mixer RIGHT output to the S1 Pro channel 2
# Set the S1 Pro channel 2 ToneMatch Switch to Guitar

==== 2 Vocals, 2 Instruments ====
====== Microphones ======
# Run both microphones to the mixer.
# On the input strips for the microphones pan all the way to the LEFT
# Run the Mixer LEFT output to the S1 Pro channel 1

====== Instruments ======
# Run both Instruments to the mixer. I used a Keyboard and an Electric Bass as examples
# On the input strips for the Instruments pan all the way to the RIGHT
# Run the Mixer RIGHT output to the Power Stand Channel 2
# Set the S1 Pro channel 2 ToneMatch Switch to Off

----
[[Category:Connections]]
[[Category:Mixer]]
[[Category:S1]]