ST at 15:48, 1 September 2018

2018-09-01T15:48:28Z

← Older revision		Revision as of 15:48, 1 September 2018
Line 1:		Line 1:
	~~When using a mixer is some of the quality lost using just the left output?~~

	~~Most small stereo mixers allow you to direct the inputs to one side or the other (two halves of the mixer). When you pan an input up the middle, you are using both halves.~~

	~~If you pan all your inputs hard LEFT and then use the LEFT output, you are using one half of the mixer. The quality should be just as good as using both halves.~~

	~~The exception: If the mixer has stereo inputs (one channel with two inputs), panning hard to one side means you will lose the other side of the stereo pair.~~

	{{KCS Article		{{KCS Article
	\|Issue =		\|Issue =
Line 15:		Line 7:

	\|Resolution =		\|Resolution =
	Most small stereo mixers allow you to direct the inputs to one side or the other (two sides of the mixer). When you pan an input up the middle, you are using both sides. The two outputs typically go to two powered loudspeakers.		Most small stereo mixers allow you to direct the inputs to one side or the other (two sides of the mixer).

			*When you pan an input up the middle, you are using both sides. The two outputs typically go to two powered loudspeakers.

	If you pan all your inputs hard LEFT and then use the LEFT output, you are using one side of the mixer and in this situation, you are connecting that to a single powered loudspeaker. The quality should be just as good as using both sides of the mixer		*When you pan all your inputs hard LEFT and then use the LEFT output, you are using one side of the mixer and in this situation, you are connecting that to a single powered loudspeaker. The quality should be just as good as using both sides of the mixer

	The exception: If the mixer has stereo inputs (one channel with two inputs), panning hard to one side means you will lose the other side of the stereo pair.		The exception: If the mixer has stereo inputs (one channel with two inputs), panning hard to one side means you will lose the other side of the stereo pair.

ST: Created article

2018-09-01T15:46:37Z

Created article

New page

When using a mixer is some of the quality lost using just the left output?

Most small stereo mixers allow you to direct the inputs to one side or the other (two halves of the mixer). When you pan an input up the middle, you are using both halves.

If you pan all your inputs hard LEFT and then use the LEFT output, you are using one half of the mixer. The quality should be just as good as using both halves.

The exception: If the mixer has stereo inputs (one channel with two inputs), panning hard to one side means you will lose the other side of the stereo pair.

{{KCS Article
|Issue =
When using a mixer is some of the quality lost using just the left output?

|Environment =
Connecting a stereo mixer to a mono {{L1}}. {{Compact}}, {{Model 1S}}, {{Model 1S}}, {{F1}}

|Resolution =
Most small stereo mixers allow you to direct the inputs to one side or the other (two sides of the mixer). When you pan an input up the middle, you are using both sides. The two outputs typically go to two powered loudspeakers.

If you pan all your inputs hard LEFT and then use the LEFT output, you are using one side of the mixer and in this situation, you are connecting that to a single powered loudspeaker. The quality should be just as good as using both sides of the mixer

The exception: If the mixer has stereo inputs (one channel with two inputs), panning hard to one side means you will lose the other side of the stereo pair.

See [[Stereo Mixer to Mono L1®]]

Related conversation [https://www.bosepro.community/g/portable/topic/l1-compact-29 L1 Compact in the Ask Bose for Help forum]

|Cause =
Not applicable to this question
|Categories =
[[Category:Stereo]]
[[Category:Model 1S]]
[[Category:Model II]]
[[Category:Mixer]]

}}

Mixer Left Output Only - Revision history

ST at 15:48, 1 September 2018

ST: Created article