Mixer / Mackie / 802-VLZ3 - Revision history

ST: /* Summary */

2010-11-02T15:45:49Z

Summary

← Older revision		Revision as of 15:45, 2 November 2010
Line 3:		Line 3:

	== Summary ==		== Summary ==
	You can use either the XLR outputs ~~on the rear panel~~ (be sure to set the MIC button "in")		You can use either the XLR outputs (be sure to set the MIC button "in")
	:- or -		:- or -
	Use the ¼ inch phone jacks ~~on the top~~.		Use the ¼ inch phone jacks.

	[[Image:Mackie802VLZ3Output.png]]		[[Image:Mackie802VLZ3Output.png]]

ST: added notes for XLR

2010-11-02T15:37:15Z

added notes for XLR

← Older revision		Revision as of 15:37, 2 November 2010
Line 16:		Line 16:


	=== ¼ Inch with suitable output===		=== Cables you can use ===
			==== XLR (balanced) to XLR (balanced) ====
			[[Image:XLRXLRMF.png\|thumb\|XLR to XLR, male to female\|right]]
			(balanced to balanced) should be fine. This is the same kind of cable you would use to connect a microphone.

			==== ¼ Inch with suitable output====
	for PS1 Powerstand Channel 1 or 2 inputs		for PS1 Powerstand Channel 1 or 2 inputs

	{{RunTROrTRSUnbalanced}}		{{RunTROrTRSUnbalanced}}

ST: New page: {{Classic icon}}{{Model I icon}} ''' Mackie 802-VLZ3 ''' == Summary == You can use either the XLR outputs on the rear panel (be sure to set the MIC button "in") :- or - Use th...

2010-11-02T15:22:51Z

New page: {{Classic icon}}{{Model I icon}} <big>''' Mackie 802-VLZ3 '''</big> == Summary == You can use either the XLR outputs on the rear panel (be sure to set the MIC button "in") :- or - Use th...

New page

{{Classic icon}}{{Model I icon}}
<big>''' Mackie 802-VLZ3 '''</big>

== Summary ==
You can use either the XLR outputs on the rear panel (be sure to set the MIC button "in")
:- or -
Use the ¼ inch phone jacks on the top.

[[Image:Mackie802VLZ3Output.png]]

Use the '''XLR''' - or - '''¼ inch phone jack''' (Tip-Sleeve) outputs to
* The {{PS1}} Channels 1 or 2 if you want to use the [[Presets/Model I and Classic|Presets]] and the [[R1 Remote]] Tone and Level Controls
<br /> OR <br />
* The {{PS1}} Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the {{PS1}} or the [[R1 Remote]].
* If you want to use the Balanced XLR outputs use the MIC setting in the picture above.

=== ¼ Inch with suitable output===
for PS1 Powerstand Channel 1 or 2 inputs

{{RunTROrTRSUnbalanced}}

Links:
* [http://www.mackie.com/products/802vlz3/pdf/802VLZ3_OM.pdf Mackie 802-VLZ3 Manual]

----
<references/>

[[Category:Mixer]]
[[Category:Mackie]]