L1 Pro to S1 Pro+ - Revision history

ST at 20:25, 1 October 2025

2025-10-01T20:25:05Z

← Older revision		Revision as of 20:25, 1 October 2025
Line 15:		Line 15:

	[[File:L1 Pro Daisy S1 Pro+ Aux.jpg\|400px\|L1 Pro Daisy S1 Pro+]]		[[File:L1 Pro Daisy S1 Pro+ Aux.jpg\|400px\|L1 Pro Daisy S1 Pro+]]

			You can also use the S1 Pro+ Wireless XLR transmitter instead of a wired connection. See [[S1 Pro+ Daisy Chain Wireless]] for details.

	----		----

ST at 17:08, 26 September 2024

2024-09-26T17:08:43Z

← Older revision		Revision as of 17:08, 26 September 2024
Line 3:		Line 3:

	#Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the {{S1 Pro+}} input three. You can also connect to channels 1 or 2, but using channel 3 is preferred because this gives the best match to the output level of the L1 Pro.		#Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the {{S1 Pro+}} input three. You can also connect to channels 1 or 2, but using channel 3 is preferred because this gives the best match to the output level of the L1 Pro.
	#* Note: The L1 Pro Line Output (XLR) is LINE LEVEL, so connect it to one of the S1 Pro 1/4 inch (6.3 mm) inputs. These are also LINE LEVEL.		#* Note: The L1 Pro Line Output (XLR) is LINE LEVEL, so connect it to one of the {{S1 Pro+}} 1/4 inch (6.3 mm) inputs. These are also LINE LEVEL.
	#* The S1 Pro XLR inputs are MICROPHONE LEVEL, and the L1 Pro LINE LEVEL output may be too hot for the XLR inputs. ~~See~~ the ~~picture at~~ the ~~bottom of this article for details~~.		#* The S1 Pro XLR inputs are MICROPHONE LEVEL, and the L1 Pro LINE LEVEL output may be too hot for the XLR inputs. If the {{S1 Pro+}} input is clipping (RED LED), turn down the channel volume.
	#Set the volume on the {{S1 Pro+}} to 10:00 o'clock and then adjust it to suit the application. If you see solid red on the {{S1 Pro+}}, turn down the channel volume.		#Set the volume on the {{S1 Pro+}} to 10:00 o'clock and then adjust it to suit the application. If you see solid red on the {{S1 Pro+}}, turn down the channel volume.

ST at 16:57, 26 September 2024

2024-09-26T16:57:05Z

← Older revision		Revision as of 16:57, 26 September 2024
Line 3:		Line 3:

	#Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the {{S1 Pro+}} input three. You can also connect to channels 1 or 2, but using channel 3 is preferred because this gives the best match to the output level of the L1 Pro.		#Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the {{S1 Pro+}} input three. You can also connect to channels 1 or 2, but using channel 3 is preferred because this gives the best match to the output level of the L1 Pro.
	#* Note: The L1 Pro Line Output (XLR) is LINE LEVEL so connect it to one of the S1 Pro 1/4 inch (6.3 mm) inputs. These are also LINE LEVEL.		#* Note: The L1 Pro Line Output (XLR) is LINE LEVEL, so connect it to one of the S1 Pro 1/4 inch (6.3 mm) inputs. These are also LINE LEVEL.
	#* The S1 Pro XLR inputs are MICROPHONE LEVEL, and the L1 Pro LINE LEVEL output is too hot for the XLR inputs. See the picture at the bottom of this article for details.		#* The S1 Pro XLR inputs are MICROPHONE LEVEL, and the L1 Pro LINE LEVEL output may be too hot for the XLR inputs. See the picture at the bottom of this article for details.
	#Set the volume on the {{S1 Pro+}} to 10:00 o'clock and then adjust to suit the application. If you see solid red on the {{S1 Pro+}} turn down the channel volume.		#Set the volume on the {{S1 Pro+}} to 10:00 o'clock and then adjust it to suit the application. If you see solid red on the {{S1 Pro+}}, turn down the channel volume.

	;Note:		;Note:
	The L1 Pro Line Out is post-fader. ~~That is, it~~ is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}).		The L1 Pro Line Out is post-fader. It is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}).

	The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref>		The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref>

ST: Created page with "{{L1 Pro icon}} {{S1 Pro+ icon}} To connect an L1 Pro system to an {{S1 Pro+}} as a monitor or an extension to the L1 Pro #Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sle..."

2024-09-26T16:33:58Z

Created page with "{{L1 Pro icon}} {{S1 Pro+ icon}} To connect an L1 Pro system to an {{S1 Pro+}} as a monitor or an extension to the L1 Pro #Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sle..."

New page

{{L1 Pro icon}} {{S1 Pro+ icon}}
To connect an L1 Pro system to an {{S1 Pro+}} as a monitor or an extension to the L1 Pro

#Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the {{S1 Pro+}} input three. You can also connect to channels 1 or 2, but using channel 3 is preferred because this gives the best match to the output level of the L1 Pro.
#* Note: The L1 Pro Line Output (XLR) is LINE LEVEL so connect it to one of the S1 Pro 1/4 inch (6.3 mm) inputs. These are also LINE LEVEL.
#* The S1 Pro XLR inputs are MICROPHONE LEVEL, and the L1 Pro LINE LEVEL output is too hot for the XLR inputs. See the picture at the bottom of this article for details.
#Set the volume on the {{S1 Pro+}} to 10:00 o'clock and then adjust to suit the application. If you see solid red on the {{S1 Pro+}} turn down the channel volume.

;Note:
The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}).

The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref>

This applies to any L1 Pro system (L1 Pro8, L1 Pro16, L1 Pro32).

[[File:L1 Pro Daisy S1 Pro+ Aux.jpg|400px|L1 Pro Daisy S1 Pro+]]

----
[[Category:L1 Pro]]
[[Category:S1 Pro+]]
[[Category:Connections]]