ST at 19:02, 22 April 2023

2023-04-22T19:02:42Z

← Older revision		Revision as of 19:02, 22 April 2023
Line 1:		Line 1:
	{{L1 Pro icon}} {{Model II icon}}		{{L1 Pro icon}} {{Model II icon}}
	To connect an L1 Pro system to a {{Model II}} as an extension of the loudspeaker.		To connect an L1 Pro system (any model) to a {{Model II}} as an extension of the loudspeaker.

	This page describes ''''how'''' to make the connections. Please also see: [[Stereo / Mono / Distributed Systems]] to read when and ''''why'''' you would do this.		This page describes ''''how'''' to make the connections. Please also see: [[Stereo / Mono / Distributed Systems]] to read when and ''''why'''' you would do this.

	[[File:Model II Analog Input Level Green.png\|right\|L1 Model II Analog Input Trim]]		[[File:Model II Analog Input Level Green.png\|right\|L1 Model II Analog Input Trim]]

ST: Created page with "{{L1 Pro icon}} {{Model II icon}} To connect an L1 Pro system to a {{Model II}} as an extension of the loudspeaker. This page describes ''''how'''' to make the connections. P..."

2023-04-22T18:59:38Z

Created page with "{{L1 Pro icon}} {{Model II icon}} To connect an L1 Pro system to a {{Model II}} as an extension of the loudspeaker. This page describes ''''how'''' to make the connections. P..."

New page

{{L1 Pro icon}} {{Model II icon}}
To connect an L1 Pro system to a {{Model II}} as an extension of the loudspeaker.

This page describes ''''how'''' to make the connections. Please also see: [[Stereo / Mono / Distributed Systems]] to read when and ''''why'''' you would do this.

[[File:Model II Analog Input Level Green.png|right|L1 Model II Analog Input Trim]]
#Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the {{Model II}} Analog Input
#Set the Analog Input Trim to 10:00 o'clock and then adjust to suit the application. If you see solid red on the {{Model II}} turn down the Analog Input Trim
;Note:
The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}). The Line Out sends a signal that matches what you hear from the L1 Pro. As you raise or lower the volume (and make other changes to the sound), this changes the output at the Line Out (except as noted in the next paragraph).

The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref>

This applies to any L1 Pro system (L1 Pro8, L1 Pro16, L1 Pro32).

[[File:L1 Pro16 to L1 Model II.jpg|400px|L1 Pro Daisy L1 Model II]]

Note;
; L1 Model II will not necessarily match the volume of the L1 Pro
Because the output level of the L1 Pro Line Out is post-fader (see above) is higher than the original source. If you set the volume control on the {{Model II}} to the same settings as the L1 Pro, the {{Model II}} may will be louder. Two get the levels the same,
# Turn down the Analog Input Trim on the {{Model II}}
# Set the level you want on the L1 Pro
# Set the volume on the {{Model II}} to suit the application. Do that by ear.

----
[[Category:L1 Pro]]
[[Category:Model II]]
[[Category:Daisy]]

[[Category:Connections]]

L1 Pro to L1 Model II - Revision history

ST at 19:02, 22 April 2023

ST: Created page with "{{L1 Pro icon}} {{Model II icon}} To connect an L1 Pro system to a {{Model II}} as an extension of the loudspeaker. This page describes ''''how'''' to make the connections. P..."