L1 Pro to L1 Compact - Revision history

ST at 16:43, 3 February 2023

2023-02-03T16:43:12Z

← Older revision		Revision as of 16:43, 3 February 2023
Line 14:		Line 14:

	[[File:L1 Pro8 to L1 Compact Daisy.jpg\|400px\|L1 Pro Daisy S1 Pro Chain]]		[[File:L1 Pro8 to L1 Compact Daisy.jpg\|400px\|L1 Pro Daisy S1 Pro Chain]]

			Note;
			; L1 Compact Louder than the First
			Because the output level of the L1 Pro Line Out is post-fader (see above) is higher than the original source. If you set the volume control on the L1 Compact to the same settings as the first L1 Pro, the L1 Compact may will be louder. Two get the levels the same,
			# Turn down the volume on the L1 Compact
			# Set the level you want on the L1 Pro
			# Set the volume on the L1 Compact to suit the application. Do that by ear.

	----		----

ST at 05:33, 17 December 2022

2022-12-17T05:33:22Z

← Older revision		Revision as of 05:33, 17 December 2022
Line 7:		Line 7:

	;Note:		;Note:
	The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}).		The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}). The Line Out sends a signal that matches what you hear from the L1 Pro. As you raise or lower the volume (and make other changes to the sound), this changes the output at the Line Out (except as noted in the next paragraph).

	The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref>		The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref>

ST: Created page with "{{L1 Pro icon}} {{Compact icon}} To connect an L1 Pro system to an {{Compact}} as a monitor or an extension of the loudspeaker #Use an XLR female to 1/4 inch (6.3 mm) Tip-Rin..."

2022-03-06T02:46:27Z

Created page with "{{L1 Pro icon}} {{Compact icon}} To connect an L1 Pro system to an {{Compact}} as a monitor or an extension of the loudspeaker #Use an XLR female to 1/4 inch (6.3 mm) Tip-Rin..."

New page

{{L1 Pro icon}} {{Compact icon}}
To connect an L1 Pro system to an {{Compact}} as a monitor or an extension of the loudspeaker

#Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the {{Compact}} Channel two (DO NOT USE channel 1 XLR)
#Set the ToneMatch switch to Line Level (down position)
#Set the volume on the {{Compact}} to 10:00 o'clock and then adjust to suit the application. If you see solid red on the {{Compact}} turn down the channel volume.

;Note:
The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}).

The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref>

This applies to any L1 Pro system (L1 Pro8, L1 Pro16, L1 Pro32).

[[File:L1 Pro8 to L1 Compact Daisy.jpg|400px|L1 Pro Daisy S1 Pro Chain]]

----
[[Category:L1 Pro]]
[[Category:Compact]]
[[Category:Daisy]]

[[Category:Connections]]