L1 Inputs General Information - Revision history

ST at 06:15, 14 September 2024

2024-09-14T06:15:51Z

← Older revision		Revision as of 06:15, 14 September 2024
Line 9:		Line 9:

	;XLR		;XLR
	: The XLR inputs are microphone-level, and you should avoid using line-level sources except ~~For~~ models with trim controls (ToneMatch Mixers) or automatic DSP trim (L1 Pro)		: The XLR inputs are microphone-level, and you should avoid using line-level sources except for models with trim controls (ToneMatch Mixers) or automatic DSP trim (L1 Pro)

	; 1/4 inch (6.3 mm) Tip-Ring-Sleeve		; 1/4 inch (6.3 mm) Tip-Ring-Sleeve

ST at 06:03, 14 September 2024

2024-09-14T06:03:33Z

← Older revision		Revision as of 06:03, 14 September 2024
Line 5:		Line 5:
	\|RightBody = The Bose Portable PA systems have several types of inputs:		\|RightBody = The Bose Portable PA systems have several types of inputs:
	* XLR/ 1/4 inch (6.3 mm) Tip-Ring-Sleeve combo jacks		* XLR/ 1/4 inch (6.3 mm) Tip-Ring-Sleeve combo jacks
	* 1/4-inch Tip-Ring-Sleeve / Tip-Sleeve jacks		* 1/4 inch (6.3 mm) Tip-Ring-Sleeve / Tip-Sleeve jacks
	* 1/8-inch Tip-Ring-Sleeve jacks		* 1/8 inch (3.5 mm) Tip-Ring-Sleeve jacks

	;XLR		;XLR
	: ~~For models without trim controls (or automatic DSP trim), the~~ XLR inputs are microphone-level, and you should avoid using line-level sources		: The XLR inputs are microphone-level, and you should avoid using line-level sources except For models with trim controls (ToneMatch Mixers) or automatic DSP trim (L1 Pro)

	; 1/4 inch (6.3 mm) Tip-Ring-Sleeve		; 1/4 inch (6.3 mm) Tip-Ring-Sleeve
Line 34:		Line 34:
	* The XLR inputs are microphone-level inputs.		* The XLR inputs are microphone-level inputs.
	* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.		* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
	* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.		* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs. These are high-impedance inputs suitable for guitars with bare piezo pickups (no electronics).
	;Note:		;Note:
	:Unlike the L1, F1, and S1 models, the ToneMatch mixers (T1, T4S/T8S) have input trim controls to adjust the input sensitivity. This means that you can connect line-level sources to the XLR inputs and adjust the input sensitivity with the trim controls.		:Unlike the L1, F1, and S1 models, the ToneMatch mixers (T1, T4S/T8S) have input trim controls to adjust the input sensitivity. This means that you can connect line-level sources to the XLR inputs and adjust the input sensitivity with the trim controls.
Line 50:		Line 50:
	=== Channel 2 ===		=== Channel 2 ===
	====1/4 inch (6.3 mm) Tip-Ring-Sleeve ====		====1/4 inch (6.3 mm) Tip-Ring-Sleeve ====
	* If you connect with a 1/4 inch (6.3mm) Tip-Sleeve input, this is an instrument-level input. If connecting a guitar, set the ToneMatch switch to Guitar (up). For other instruments, set the ToneMatch switch to Line (down).		* If you connect with a 1/4 inch (6.3mm) Tip-Sleeve input, this is an instrument-level input. This is a high-impedance input suitable for guitars with bare piezo pickups (no electronics). If connecting a guitar, set the ToneMatch switch to Guitar (up). For other instruments, set the ToneMatch switch to Line (down).
	* If you connect with a 1/4 inch (6.3 mm) Tip-Ring-Sleeve jack, this is a balanced line-level input. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. A 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain. Set the ToneMatch switch to Line (down).		* If you connect with a 1/4 inch (6.3 mm) Tip-Ring-Sleeve jack, this is a balanced line-level input. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. A 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain. Set the ToneMatch switch to Line (down).
	==== 1/8 inch Tip-Ring-Sleeve ====		==== 1/8 inch (3.5 mm) Tip-Ring-Sleeve ====
	This is a stereo input for consumer line-level inputs. The left and right channels are buffered to mono.		This is a stereo input for consumer line-level inputs. The left and right channels are buffered to mono.

Line 65:		Line 65:

	== L1 Pro ==		== L1 Pro ==
	=== Combo Jacks (~~Inputs~~ 1 and 2) ===		=== Combo Jacks (Channels 1 and 2) ===
	* The XLR inputs are microphone-level inputs.		* The XLR inputs are microphone-level inputs.
	* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.		* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
	* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.		* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs. These are high-impedance inputs suitable for guitars with bare piezo pickups (no electronics).

	The L1 Pro systems are unique among all the Bose Portable PA systems because a Digital Signal Processor automatically sets the input gain (like an automatic trim control).		The L1 Pro systems are unique among all the Bose Portable PA systems because a Digital Signal Processor automatically sets the input gain (like an automatic trim control).

	Trim: The DSP automatically selects and compensates 0 dB, 12 dB, 24 dB, 36 dB, and 45 dB analog gain steps. This means that you can connect line-level sources to the XLR inputs, and the DSP will adjust the input sensitivity automatically.		Trim: The DSP automatically selects and compensates 0 dB, 12 dB, 24 dB, 36 dB, and 45 dB analog gain steps. This means that you can connect line-level sources to the XLR inputs, and the DSP will adjust the input sensitivity automatically.

			=== 1/4 inch (6.3 mm) Tip-Ring-Sleeve (Channel 3) ===
			This is a balanced line-level input. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug.

			A 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain compared to a balanced connection.

			This also accepts instrument-level sources except guitars without a built-in preamp.

			==== 1/8 inch (3.5 mm) Tip-Ring-Sleeve ====
			This is a stereo input for consumer line-level inputs. The left and right channels are buffered to mono.


	== S1 Pro ==		== S1 Pro ==
Line 78:		Line 89:
	* The XLR inputs are microphone-level inputs.		* The XLR inputs are microphone-level inputs.
	* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.		* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
	* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.		* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs. These are high-impedance inputs suitable for guitars with bare piezo pickups (no electronics).


Line 85:		Line 96:
	* The XLR inputs are microphone-level inputs.		* The XLR inputs are microphone-level inputs.
	* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.		* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
	* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.		* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs. These are high-impedance inputs suitable for guitars with bare piezo pickups (no electronics).

	=== Aux Input ===		=== Aux Input ===
	This refers to the 1/4 inch (6.3 mm) Tip-Ring-Sleeve Aux Jack on channel 3		This refers to the 1/4 inch (6.3 mm) Tip-Ring-Sleeve Aux Jack on channel 3

	This is a balanced line-level input. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. Using a 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain.		This is a balanced line-level input. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. Using a 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain compared to a balanced connection.


			This also accepts instrument-level sources except guitars without a built-in preamp.

	== F1 812 ==		== F1 812 ==

ST at 05:51, 14 September 2024

2024-09-14T05:51:28Z

← Older revision		Revision as of 05:51, 14 September 2024
Line 1:		Line 1:
	{{DivToc		{{DivToc

	\|RightHead = ~~Inputs for Various Models~~		\|RightHead = Introduction

	\|RightBody = The Bose Portable PA systems have several types of inputs:		\|RightBody = The Bose Portable PA systems have several types of inputs:

ST at 05:49, 14 September 2024

2024-09-14T05:49:45Z

@@ Line 1: / Line 1: @@
-General information about inputs
+{{DivToc
 == ToneMatch Mixers (T1, T4S/T8S)  ==
 === Combo Jacks ===

ST: /* L1 Model II/ Model 1S */

2024-09-14T05:22:44Z

L1 Model II/ Model 1S

@@ Line 13: / Line 13: @@
 * On the T8S the Aux inputs are 9/10
 These are balanced line-level inputs. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. Using a 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain.
 == L1 Model II/ Model 1S==

ST: /* Combo Jacks (Inputs 1 and 2) */

2024-09-14T01:43:21Z

Combo Jacks (Inputs 1 and 2)

← Older revision		Revision as of 01:43, 14 September 2024
Line 30:		Line 30:
	The L1 Pro systems are unique among all the Bose Portable PA systems because a Digital Signal Processor automatically sets the input gain (like an automatic trim control).		The L1 Pro systems are unique among all the Bose Portable PA systems because a Digital Signal Processor automatically sets the input gain (like an automatic trim control).

	Trim: 0 dB, 12 dB, 24 dB, 36 dB, and 45 dB analog gain steps ~~are automatically selected~~ and ~~compensated by~~ DSP		Trim: The DSP automatically selects and compensates 0 dB, 12 dB, 24 dB, 36 dB, and 45 dB analog gain steps. This means that you can connect line-level sources to the XLR inputs, and the DSP will adjust the input sensitivity automatically.

	== S1 Pro ==		== S1 Pro ==

ST: /* ToneMatch Mixers (T1, T4S/T8S) */

2024-09-14T01:42:02Z

ToneMatch Mixers (T1, T4S/T8S)

← Older revision		Revision as of 01:42, 14 September 2024
Line 6:		Line 6:
	* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.		* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.
	;Note:		;Note:
	:Unlike the L1, F1, and S1 models, the ToneMatch mixers (T1, T4S/T8S) have input trim controls to adjust the input sensitivity.		:Unlike the L1, F1, and S1 models, the ToneMatch mixers (T1, T4S/T8S) have input trim controls to adjust the input sensitivity. This means that you can connect line-level sources to the XLR inputs and adjust the input sensitivity with the trim controls.

	=== Aux Inputs ===		=== Aux Inputs ===

ST at 01:37, 14 September 2024

2024-09-14T01:37:10Z

← Older revision		Revision as of 01:37, 14 September 2024
Line 13:		Line 13:
	* On the T8S the Aux inputs are 9/10		* On the T8S the Aux inputs are 9/10
	These are balanced line-level inputs. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. Using a 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain.		These are balanced line-level inputs. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. Using a 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain.

			== L1 Model II/ Model 1S==
			=== Power Stand Analog Input ===
			This is a 1/4 inch (6.3 mm) Tip-Ring-Sleeve jack.

			It is a balanced line-level input. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. A 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain.

			Adjust the input level with the Analog Input Trim control. Set the trim so the LED light is a solid green. If you see red, turn it down.

	== L1 Pro ==		== L1 Pro ==
Line 20:		Line 28:
	* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.		* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.

	The L1 Pro systems are unique among all the Bose Portable PA systems because ~~there is~~ a Digital Signal Processor ~~that~~ automatically sets the input gain (like an automatic trim control).		The L1 Pro systems are unique among all the Bose Portable PA systems because a Digital Signal Processor automatically sets the input gain (like an automatic trim control).

	Trim: 0 dB, 12 dB, 24 dB, 36 dB, and 45 dB analog gain steps are automatically selected and compensated by DSP		Trim: 0 dB, 12 dB, 24 dB, 36 dB, and 45 dB analog gain steps are automatically selected and compensated by DSP

ST: /* ToneMatch Mixers (T1, T4S/T8S */

2024-09-14T01:29:26Z

ToneMatch Mixers (T1, T4S/T8S

← Older revision		Revision as of 01:29, 14 September 2024
Line 1:		Line 1:
	General information about inputs		General information about inputs
	== ToneMatch Mixers (T1, T4S/T8S ==		== ToneMatch Mixers (T1, T4S/T8S) ==
	=== Combo Jacks ===		=== Combo Jacks ===
	* The XLR inputs are microphone-level inputs.		* The XLR inputs are microphone-level inputs.

ST: Created page with "General information about inputs == ToneMatch Mixers (T1, T4S/T8S == === Combo Jacks === * The XLR inputs are microphone-level inputs. * The 1/4-inch Tip-Ring-Sleeve jacks ar..."

2024-09-14T01:28:51Z

Created page with "General information about inputs == ToneMatch Mixers (T1, T4S/T8S == === Combo Jacks === * The XLR inputs are microphone-level inputs. * The 1/4-inch Tip-Ring-Sleeve jacks ar..."

New page

General information about inputs
== ToneMatch Mixers (T1, T4S/T8S ==
=== Combo Jacks ===
* The XLR inputs are microphone-level inputs.
* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.
;Note:
:Unlike the L1, F1, and S1 models, the ToneMatch mixers (T1, T4S/T8S) have input trim controls to adjust the input sensitivity.

=== Aux Inputs ===
* The T1 4/5 inputs are Aux inputs.
* On the T4S the Aux inputs are 5/6
* On the T8S the Aux inputs are 9/10
These are balanced line-level inputs. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. Using a 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain.

== L1 Pro ==
=== Combo Jacks (Inputs 1 and 2) ===
* The XLR inputs are microphone-level inputs.
* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.

The L1 Pro systems are unique among all the Bose Portable PA systems because there is a Digital Signal Processor that automatically sets the input gain (like an automatic trim control).

Trim: 0 dB, 12 dB, 24 dB, 36 dB, and 45 dB analog gain steps are automatically selected and compensated by DSP

== S1 Pro ==
=== Combo Jacks (Inputs 1 and 2) ===
* The XLR inputs are microphone-level inputs.
* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.

== S1 Pro+ ==
=== Combo Jacks (Inputs 1 and 2) ===
* The XLR inputs are microphone-level inputs.
* The 1/4-inch Tip-Ring-Sleeve jacks are line-level inputs.
* When you connect a 1/4-inch (6.3mm) Tip-Sleeve connector to the 1/4-inch jacks, they are instrument-level inputs.

=== Aux Input ===
This refers to the 1/4 inch (6.3 mm) Tip-Ring-Sleeve Aux Jack on channel 3

This is a balanced line-level input. Use balanced connections with a 1/4-inch Tip-Ring-Sleeve plug. Using a 1/4 inch (6.3mm) Tip-Sleeve plug creates an unbalanced connection and loses up to -6 dB gain.

== F1 812 ==
The F1 systems have a mic/line level input sensitivity switch on input one.

----
[[Category:L1 Pro]]
[[Category:T1]]
[[Category:T4S]]
[[Category:T8S]]
[[Category:F1]]
[[Category:S1 Pro]]
[[Category:S1 Pro+]]