L1® Model II with Mixer to Analog Input - Revision history

ST: Added {{#lst:L1®_Model_II|AnalogInput}}

2019-09-30T23:32:12Z

Added {{#lst:L1®_Model_II|AnalogInput}}

← Older revision		Revision as of 23:32, 30 September 2019
Line 15:		Line 15:

	You cannot 'get through the gig' this way if you are a DJ or if you need to run prerecorded music or have stereo inputs.		You cannot 'get through the gig' this way if you are a DJ or if you need to run prerecorded music or have stereo inputs.

			{{#lst:L1®_Model_II\|AnalogInput}}
	----		----
	[[Category:Model II]]		[[Category:Model II]]
	[[Category:Mixer]]</noinclude>		[[Category:Mixer]]</noinclude>

ST: ST moved page L1Â® Model II with Mixer to Analog Input to L1® Model II with Mixer to Analog Input

2017-03-26T09:27:21Z

ST moved page L1Â® Model II with Mixer to Analog Input to L1® Model II with Mixer to Analog Input

← Older revision	Revision as of 09:27, 26 March 2017
(No difference)

ST at 14:10, 28 July 2010

2010-07-28T14:10:19Z

← Older revision		Revision as of 14:10, 28 July 2010
Line 8:		Line 8:

	<noinclude>		<noinclude>
			'''A ¼ inch Tip-Ring-Sleeve connector carrying a stereo signal should not be used with the analog input on the Model II.'''

			Even though a ¼ inch Tip-Ring-Sleeve connector can carry a stereo signal this is not how this physical connection is used on the {{PAGENAME}} Power Stand.

			The analog input on the Model II is balanced, and will therefore subtract the Left and Right signals on a stereo cable and you will hear an L-R (Left minus Right) signal in the Model II.

			You cannot 'get through the gig' this way if you are a DJ or if you need to run prerecorded music or have stereo inputs.
	----		----
	[[Category:Model II]]		[[Category:Model II]]
	[[Category:Mixer]]</noinclude>		[[Category:Mixer]]</noinclude>

ST: first ed

2010-07-28T14:03:45Z

first ed

New page

[[Image:ModelIISystemLeftFacing.jpg|100px|right|L1 Model II]]
[[Image:AlesisMultiMix8USB.jpg|75px|Alesis MultiMix8USB]][[Image:BehringerUB1202.png|75px|Behringer UB1202]][[Image:Mackie1202VLZPro.png|75px|Mackie 1202 VLZ Pro]][[Image:NumarkCDMix-2.png|75px|Numark CD Mix-2]][[Image:SoundCraftSpiritNotepad.png|100px|Spirit Notepad]][[Image:YamahaMG82FX.png|75px|Yamaha MG82/FX]]

If you are using a mixer instead of a {{T1}} use the mixer to create a mono output and send that to the Model II Power Stand Analog input.
* If there is a stereo/mono switch then use it and send the mono output to the Model II Power Stand Analog input.
* If there is a Left/mono output then use that and send it to the Model II Power Stand Analog input.
* If there is no way to create a mono output then pan all your mixer inputs all the way to one side (e.g. Left) and then take the mixer for that side (e.g. Left) output and send it to the Model II Power Stand Analog input.

<noinclude>
----
[[Category:Model II]]
[[Category:Mixer]]</noinclude>