Effects for the PS1 Powerstand - Revision history

ST: Summary of Lines Out from the Power Stand

2010-07-08T15:34:34Z

Summary of Lines Out from the Power Stand

← Older revision		Revision as of 15:34, 8 July 2010
Line 55:		Line 55:

	This will give you the same thing. These cables come in different lengths, so you can choose what you need.		This will give you the same thing. These cables come in different lengths, so you can choose what you need.



			== Summary of Lines Out from the Power Stand ==
			{{#lst:PS1 Powerstand Connections / Line Out\|Connections}}


	----		----

ST: ==== Custom Cable TRS to TS ====

2007-06-09T03:14:17Z

==== Custom Cable TRS to TS ====

← Older revision		Revision as of 03:14, 9 June 2007
Line 42:		Line 42:
	{{:Half Insert}}		{{:Half Insert}}

			==== Custom Cable TRS to TS ====
	There is a workaround to avoid the "[[Half Insert\|half-way]]" insert cable. If your handy with a soldering iron you can make a cable with one 1/4" [[TRS]] (tip ring sleeve, stereo) and one normal 1/4" (mono) plug. On the [[TRS]] end connect the tip and the ring together, then simply proceed like you would with an ordinary guitar cable (on both ends: wire shield goes to sleeve, and wire core goes to tip). The [[TRS]] end goes into the PS1 insert, the [[TS]] into the input of your effects unit. Be sure to label the cable properly.		There is a workaround to avoid the "[[Half Insert\|half-way]]" insert cable. If your handy with a soldering iron you can make a cable with one 1/4" [[TRS]] (tip ring sleeve, stereo) and one normal 1/4" (mono) plug. On the [[TRS]] end connect the tip and the ring together, then simply proceed like you would with an ordinary guitar cable (on both ends: wire shield goes to sleeve, and wire core goes to tip). The [[TRS]] end goes into the PS1 insert, the [[TS]] into the input of your effects unit. Be sure to label the cable properly.

ST: Category:Effects

2007-05-27T16:48:19Z

Category:Effects

← Older revision		Revision as of 16:48, 27 May 2007
Line 58:		Line 58:
	<references/>		<references/>

			[[Category:Effects]]
	[[Category:Effects PS1 Powerstand]]		[[Category:Effects PS1 Powerstand]]
	[[Category:PS1 Powerstand]]		[[Category:PS1 Powerstand]]

ST: table formatting for TOC

2007-05-27T16:47:11Z

table formatting for TOC

← Older revision		Revision as of 16:47, 27 May 2007
Line 1:		Line 1:
			{{Model I icon}}{{Classic icon}}
	<table><tr>		<table><tr>
	<td valign="top" width="200">__TOC__</td>		<td valign="top" width="200">__TOC__</td>
	<td valign="top">		<td valign="top">
	~~{{Model I icon}}{{Classic icon}}~~		[[Image:PS1InsertPoints.png\|550px\|right\|Powerstand Insert Point]]
	[[Image:PS1InsertPoints.png\|~~450px~~\|right\|Powerstand Insert Point]]
	</td>		</td>
	</tr></table>		</tr></table>

ST: {{Model I icon}}{{Classic icon}}

2007-05-27T16:46:06Z

← Older revision		Revision as of 16:46, 27 May 2007
Line 1:		Line 1:
	<~~big~~>~~'''Effects and the PS1'''~~</~~big~~> [[Image:PS1InsertPoints.png\|right\|Powerstand Insert Point]]		<table><tr>
			<td valign="top" width="200">__TOC__</td>
			<td valign="top">
			{{Model I icon}}{{Classic icon}}
			[[Image:PS1InsertPoints.png\|450px\|right\|Powerstand Insert Point]]
			</td>
			</tr></table>


	Hilmar-at-Bose wrote <ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/2196091194?r=2196091194#2196091194 Hilmar-at-Bose's post in the Bose® Musicians Community Message Boards]</ref>		Hilmar-at-Bose wrote <ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/2196091194?r=2196091194#2196091194 Hilmar-at-Bose's post in the Bose® Musicians Community Message Boards]</ref>

ST at 03:41, 27 May 2007

2007-05-27T03:41:39Z

← Older revision		Revision as of 03:41, 27 May 2007
Line 1:		Line 1:
	<big>'''Effects and the PS1'''</big>		<big>'''Effects and the PS1'''</big> [[Image:PS1InsertPoints.png\|right\|Powerstand Insert Point]]
	Hilmar-at-Bose wrote <ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/2196091194?r=2196091194#2196091194 Hilmar-at-Bose's post in the Bose® Musicians Community Message Boards]</ref>		Hilmar-at-Bose wrote <ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/2196091194?r=2196091194#2196091194 Hilmar-at-Bose's post in the Bose® Musicians Community Message Boards]</ref>

ST: Added images inline instead of links

2007-01-13T10:43:19Z

Added images inline instead of links

← Older revision		Revision as of 10:43, 13 January 2007
Line 7:		Line 7:
	=== Serial ===		=== Serial ===
	The first method is often called "serial". All effects are connected in a chain and the signal is processed sequentially in each effects processor. Nearly all stomp boxes for guitar work that way. A typical example would be and overdrive followed by a reverb. In a serial effects hookup the order in which effects matters, e.g. it makes a big difference whether you run first through the overdrive and then the reverb or first through the reverb and then through the overdrive.		The first method is often called "serial". All effects are connected in a chain and the signal is processed sequentially in each effects processor. Nearly all stomp boxes for guitar work that way. A typical example would be and overdrive followed by a reverb. In a serial effects hookup the order in which effects matters, e.g. it makes a big difference whether you run first through the overdrive and then the reverb or first through the reverb and then through the overdrive.
	[[~~Media~~:EffectsSerial.gif\|~~Click to see an~~ image from the manual: Serial Effects]]
			[[Image:EffectsSerial.gif\|image from the manual: Serial Effects]]

	=== Parallel ===		=== Parallel ===
	The second method is referred to as "parallel". This is mainly implemented in conventional mixers through the Aux or Effect Send/Return connections and controls. Here every effects processor gets the original (unprocessed) signal as an input. The output of all effects processors is then added together and summed with the original clean signal. One point of note is that in the parallel connection, there is always a component of the original signal present in the output. A typical example would be reverb and a delay which are used for vocals.		The second method is referred to as "parallel". This is mainly implemented in conventional mixers through the Aux or Effect Send/Return connections and controls. Here every effects processor gets the original (unprocessed) signal as an input. The output of all effects processors is then added together and summed with the original clean signal. One point of note is that in the parallel connection, there is always a component of the original signal present in the output. A typical example would be reverb and a delay which are used for vocals.
	[[~~Media~~:EffectsParallel.gif\|~~Click to see an~~ image from the manual: Parallel Effects]]
			[[Image:EffectsParallel.gif\|image from the manual: Parallel Effects]]

	== Which one should I use ? ==		== Which one should I use ? ==
Line 21:		Line 23:
	To connect one or more effects serially simply use the insert jack on the {{PS1}} . You probably will need an “insert” cable that has one [[TRS]] (stereo) 1/4” connector on one side and 2 mono 1/4” connectors on the other side.		To connect one or more effects serially simply use the insert jack on the {{PS1}} . You probably will need an “insert” cable that has one [[TRS]] (stereo) 1/4” connector on one side and 2 mono 1/4” connectors on the other side.

	[[Image:HosaSTP204.png~~\|thumb~~\|Hosa STP204 Insert Cable]]		[[Image:HosaSTP204.png\|Hosa STP204 Insert Cable]]

ST at 10:38, 13 January 2007

2007-01-13T10:38:27Z

← Older revision		Revision as of 10:38, 13 January 2007
Line 19:		Line 19:
	Using serial effect connection with the {{PS1}}.		Using serial effect connection with the {{PS1}}.

	To connect one or more effects serially simply use the insert jack on the {{PS1}} . You probably will need an “insert” cable that has one [[TRS]] (stereo) 1/4” connector on one side and 2 mono 1/4” connectors on the other side. These are available at your local music store or from any music instrument internet retailer such as this. The mono 1/4” plug labeled “send” or “ring” connects to the input of your effects processor and the one labeled “return” or “tip” to the output.		To connect one or more effects serially simply use the insert jack on the {{PS1}} . You probably will need an “insert” cable that has one [[TRS]] (stereo) 1/4” connector on one side and 2 mono 1/4” connectors on the other side.

			[[Image:HosaSTP204.png\|thumb\|Hosa STP204 Insert Cable]]


			These are available at your local music store or from any music instrument internet retailer such as this. The mono 1/4” plug labeled “send” or “ring” connects to the input of your effects processor and the one labeled “return” or “tip” to the output.

	=== Parallel ===		=== Parallel ===

ST: /* Half Insert Method */

2006-11-06T23:02:37Z

Half Insert Method

← Older revision		Revision as of 23:02, 6 November 2006
Line 29:		Line 29:
	There is a workaround to avoid the "[[Half Insert\|half-way]]" insert cable. If your handy with a soldering iron you can make a cable with one 1/4" [[TRS]] (tip ring sleeve, stereo) and one normal 1/4" (mono) plug. On the [[TRS]] end connect the tip and the ring together, then simply proceed like you would with an ordinary guitar cable (on both ends: wire shield goes to sleeve, and wire core goes to tip). The [[TRS]] end goes into the PS1 insert, the [[TS]] into the input of your effects unit. Be sure to label the cable properly.		There is a workaround to avoid the "[[Half Insert\|half-way]]" insert cable. If your handy with a soldering iron you can make a cable with one 1/4" [[TRS]] (tip ring sleeve, stereo) and one normal 1/4" (mono) plug. On the [[TRS]] end connect the tip and the ring together, then simply proceed like you would with an ordinary guitar cable (on both ends: wire shield goes to sleeve, and wire core goes to tip). The [[TRS]] end goes into the PS1 insert, the [[TS]] into the input of your effects unit. Be sure to label the cable properly.

	If your not comfortable making a cable like this yourself you can buy a regular "insert" cable, like this and cascade it with a [[TS]] "Y-cable", like this [http://www.sweetwater.com/store/detail/YPP111/ Hosa YPP111].

	[[~~Image:HosaYPP111.jpg~~]]		If your not comfortable making a cable like this yourself you can buy a regular "insert" cable, like this

			{{:Insert Cable}}

			and cascade it with a [[TS]] "Y-cable", like this

			{{:TS MaleTo2Female}}

	This will give you the same thing. These cables come in different lengths, so you can choose what you need.		This will give you the same thing. These cables come in different lengths, so you can choose what you need.

ST: /* Half Insert Method */ included images

2006-11-06T22:54:40Z

Half Insert Method: included images

← Older revision		Revision as of 22:54, 6 November 2006
Line 29:		Line 29:
	There is a workaround to avoid the "[[Half Insert\|half-way]]" insert cable. If your handy with a soldering iron you can make a cable with one 1/4" [[TRS]] (tip ring sleeve, stereo) and one normal 1/4" (mono) plug. On the [[TRS]] end connect the tip and the ring together, then simply proceed like you would with an ordinary guitar cable (on both ends: wire shield goes to sleeve, and wire core goes to tip). The [[TRS]] end goes into the PS1 insert, the [[TS]] into the input of your effects unit. Be sure to label the cable properly.		There is a workaround to avoid the "[[Half Insert\|half-way]]" insert cable. If your handy with a soldering iron you can make a cable with one 1/4" [[TRS]] (tip ring sleeve, stereo) and one normal 1/4" (mono) plug. On the [[TRS]] end connect the tip and the ring together, then simply proceed like you would with an ordinary guitar cable (on both ends: wire shield goes to sleeve, and wire core goes to tip). The [[TRS]] end goes into the PS1 insert, the [[TS]] into the input of your effects unit. Be sure to label the cable properly.

	If your not comfortable making a cable like this yourself you can buy a regular "insert" cable, like this and cascade it with a [[TS]] "Y-cable", like this [http://www.sweetwater.com/store/detail/YPP111/ Hosa YPP111]. This will give you the same thing. These cables come in different lengths, so you can choose what you need.		If your not comfortable making a cable like this yourself you can buy a regular "insert" cable, like this and cascade it with a [[TS]] "Y-cable", like this [http://www.sweetwater.com/store/detail/YPP111/ Hosa YPP111].

			[[Image:HosaYPP111.jpg]]

			This will give you the same thing. These cables come in different lengths, so you can choose what you need.

	----		----