B1 Rotate the Logos - Revision history

ST at 14:42, 8 July 2013

2013-07-08T14:42:38Z

← Older revision		Revision as of 14:42, 8 July 2013
Line 3:		Line 3:
	[[Image:B1LogoRotate.jpg]]		[[Image:B1LogoRotate.jpg]]

	Be very careful with the fine ends of the logo because they can be easily broken off. You may even try to pull up in the middle with your fingernails on the edge instead of near the ends.		<span style="color:red;font-weight:bold">Be very careful with the fine ends of the logo because they can be easily broken off</span>. You may even try to pull up in the middle with your fingernails on the edge instead of near the ends.

	<table><tr><td>Go from this</td><td>to this</td></tr>		<table><tr><td>Go from this</td><td>to this</td></tr>

ST at 03:07, 18 August 2011

2011-08-18T03:07:26Z

← Older revision		Revision as of 03:07, 18 August 2011
Line 20:		Line 20:
	[[Image:Rotateb104.jpg\|640px]]		[[Image:Rotateb104.jpg\|640px]]

	~~Make~~ sure that the logo is flush with the grille so that it does not rattle when the music is playing.		After you rotate the logo make sure that the logo is flush with the grille so that it does not rattle when the music is playing.

	----		----
	[[Category:B1]]		[[Category:B1]]

ST at 16:37, 17 August 2011

2011-08-17T16:37:37Z

← Older revision		Revision as of 16:37, 17 August 2011
Line 1:		Line 1:

	You can rotate the Bose logo so it is parallel to the floor even if you have turned the B1 on its side. Chuck-at-Bose said, "... Maybe it's my kung fu grip, but I've had good luck with carefully pinching the logo and pulling at these points, then rotating 90 degrees:"		You can rotate the Bose logo so it is parallel to the floor even if you have turned the B1 on its side. Chuck-at-Bose said, "... Maybe it's my kung fu grip, but I've had good luck with carefully pinching the logo and pulling at these points, then rotating 90 degrees:"

Line 5:		Line 4:

	Be very careful with the fine ends of the logo because they can be easily broken off. You may even try to pull up in the middle with your fingernails on the edge instead of near the ends.		Be very careful with the fine ends of the logo because they can be easily broken off. You may even try to pull up in the middle with your fingernails on the edge instead of near the ends.

	~~Pull the logo straight out about ½ inch before you attempt to turn it. It is spring loaded, and the rear post is square. You have to clear the post (about ½ inch before you can turn it).~~

	<table><tr><td>Go from this</td><td>to this</td></tr>		<table><tr><td>Go from this</td><td>to this</td></tr>
Line 13:		Line 10:
	</table>		</table>

	Pull straight out		Pull the logo straight out about ½ inch before you attempt to turn it. It is spring loaded, and the rear post is square. You have to clear the post (about ½ inch before you can turn it).

	[[Image:Rotateb103.jpg\|640px]]		[[Image:Rotateb103.jpg\|640px]]

	Another look. ~~The hole behind the logo is square.~~		Another look.



	[[Image:Rotateb104.jpg\|640px]]		[[Image:Rotateb104.jpg\|640px]]

ST: New page: You can rotate the Bose logo so it is parallel to the floor even if you have turned the B1 on its side. Chuck-at-Bose said, "... Maybe it's my kung fu grip, but I've had good luck with ca...

2011-08-17T16:35:49Z

New page: You can rotate the Bose logo so it is parallel to the floor even if you have turned the B1 on its side. Chuck-at-Bose said, "... Maybe it's my kung fu grip, but I've had good luck with ca...

New page

You can rotate the Bose logo so it is parallel to the floor even if you have turned the B1 on its side. Chuck-at-Bose said, "... Maybe it's my kung fu grip, but I've had good luck with carefully pinching the logo and pulling at these points, then rotating 90 degrees:"

[[Image:B1LogoRotate.jpg]]

Be very careful with the fine ends of the logo because they can be easily broken off. You may even try to pull up in the middle with your fingernails on the edge instead of near the ends.

Pull the logo straight out about ½ inch before you attempt to turn it. It is spring loaded, and the rear post is square. You have to clear the post (about ½ inch before you can turn it).

<table><tr><td>Go from this</td><td>to this</td></tr>
<tr><td>[[Image:Rotateb101.jpg]]</td>
<td>[[Image:Rotateb102.jpg]]</td></tr>
</table>

Pull straight out

[[Image:Rotateb103.jpg|640px]]

Another look. The hole behind the logo is square.

[[Image:Rotateb104.jpg|640px]]

Make sure that the logo is flush with the grille so that it does not rattle when the music is playing.

----
[[Category:B1]]